ccnp tshoot multiple choice questions

ccnp tshoot multiple choice questions

The bandwidth of F0/0 port is 100M , and the bandwidth of S0/0 port is 1.544M . Except for the next time, it is just 1:60. DMZ-Link Bw 193 kbytes is an extended community attribute, so if you want to pass this value to the just IBGP neighbor in the AS , you need to add send-community and add the extended keyword. There are 2 forwarders (1 active) The ETHERNET_SNAP frame can be used to transport multiple protocols. Therefore, SNAP can be seen as an extension that allows vendors to create their own Ethernet transport protocols. PBR (Policy Routing) 10.1.13.1 Access-list 1 permit 1.1.1.0 200 i R2 BGP table version is 1, local router ID is 4.4.4.4 Y Community R3 receives two routes, respectively carrying the community attribute as above. Now, we only want to delete the no-export attribute of the 11 route . The above match statement is used to match the neighbor IP that sent the summary route . If you specify a copy attributes option, is inject the specific routes will inherit the path attribute of the aggregated route, or breakdown will be as locally generated routes. Interface vlan 10 Switch(config-if)# spanning-tree [ vlan vlan-id ] port-priority pri 192.168.255.0/24 . TCN BPDU Off: EtherChannel not configured on interface [Experiment 3 ] No main class network; there is a default route, take the default route Look at the above picture, the gray space 172.16.0.0/16 , this network number,ccnp tshoot multiple choice questions, we call the main class network number , the so-called main class network number, meaning the network number, according to the IP address category to which it belongs , corresponding to The network number obtained after the default subnet mask length. Such as 172.16.0.0 this is a At the same time, if 172.16.1.0 and 172.16.2.0 are all DOWNed at this time , the summary route also disappears. VLAN isolated from each other, the broadcast can not cross VLAN communication, and therefore a different VLAN devices unable to reach between the general, different VLAN need to communicate with each other between the layer 3 device ? RIP Version 2 Protocol Applicability Statement *>i100.0.2.0/24 Neighbor V AS MsgRcvd The configuration of R3 is as follows: learner IP nodes can communicate, and communication is actually the process of data interaction. Data interaction requires network devices to help us transfer data between two communication nodes. When the router (or other Layer 3 device) receives an IP packet, the router will find out the purpose of the IP packet in the Layer 3 header. R5#show ip bgp 11.11.11.0 Tag rewrite with Fa1/0, 10.1.13.3, tags imposed: {} via 10.1.12.2, FastEthernet0/0, 0 dependencies OSPF and IBGP route re-release Will be reflected to other clients, non-clients and EBGP neighbors. : Enabled Example 2 of ip community-list (logical relationship): Detailed rules Path $ Logical aggregation of similar links Redistribute routes to the protocol 10.1.23.2 At this time, R1 is preferred . If you want R2 to be preferred R3 ? R2 is added as follows: The default is 6 update cycles, which is 180s . The route entry tag when an entry with a larger hop count is received Experiment 2: weighted Note that the as-path access-list is also implicitly rejecting all by default. ? Figure 2 R1 and R3 are the same AS , and the route of the 13 network segment is updated to R2 at the same time . The experimental effect is also in accordance with the rule description. If it is in the IBGP environment, that is, R1 , R2 , and R3 are all in one AS , then the rule Rules do not apply Load balancing The traditional STP , which is 802.1D , is that all VLANs share a spanning tree. The advantage of this is that the switch does not use too much resources to calculate multiple spanning trees. However, the defect is that the port is fixed through the block . As a result, traffic on the network only goes to one side, and some links have no traffic at all, which wastes bandwidth. Four types of AS_PATH path attributes BPDU sending bridge ID Default route If you want to modify the weight , let R4 go to 100.0.1.0 and go to R3 to go to 100.0.2.0 and go to R5 ? Then the configuration is modified as follows: In 802.1D , the TYPE field uses only the highest and lowest bits to indicate TC and TC acknowledgment, and RSTP extends this field: Update it; however, it does not send its secondary address 11.0.0.0 segment from fast0/0 to R1 (unless the split horizon is turned off). 5 Ip sla monitor 1 On: channel member without negotiation ( no protocol ) i New link Link1 between A and Root Router bgp 64512 no synchronization no auto-summary Then you can use the route-map tool, that is, we can associate a route-map with the re-release , to implement the function I just mentioned. 16 bits BGP routing table entry for 11.11.11.0/24, version 2 Weight Heavy FAQ published Configuring Example 6 Deploying Distribution Lists When Republishing Between Protocols Various types of ports of a Layer 3 switch Implementation point 42 We use ip ospf cost 100 on the F0/0 port of R4 to increase the interface cost , so the result is as follows: The MAC address is burned in the ROM of the Network Interface Controller (NIC ) . Access-list 1 permit any route-map PBR permit 10 match ip address 1 802.1D situation: Invalid timer When the network is normal, the data is forced to go ISP1 , ping 100 remote network data to ISP1 R2(config)# router ospf 1 5.5.5.5 Bridge ID in the MAC , is the backplane of the switch MAC , the port ID in the MAC switch port MAC , all the view switch mac available Lab topology and description You can also use the show ip dhcp bingding to capture the client-identifier of the client on the server. Ip default-gateway 108 Think carefully about what will be wrong, in fact access-list 1 deny 172.16.32.0 is a summary route 172.16. 32.0/21 Configuration and implementation Each cluster has a unique cluster ID AS does not compare the MED values. In other words, for multiple paths, the MED is compared only if the first AS in AS_SEQUENCE is the same ; any leading AS_CONFED_SEQUENCE will be ignored. MED only affects traffic between directly connected autonomous systems, and does not pass across ASs. The frame to which the Native VLAN belongs is not tagged when it passes the trunk . The first 8 bits of the route must match the first 8 bits of 172.0.0.0 , the other bits are not concerned, and the mask must be /8 . In R2 , the energy from each R1 and R3 learning to 100.0 the EBGP route, if arranged on maximum-paths 2 Network In the above figure, two routers , R1 and R2 , exchange information with each other through RIP . However, since RIPv2 sends routing updates and related messages based on multicast, once two routers activate RIP on the interface , the PC will have to consume resources to process these multicast messages that it does not need.