Free Cisco Written Dumps
For Top 50 Purchases 01:59:56


ccie lab uk


ProblemServer 1 can not get ip address.


SW3#show ip dhcp snooping  

Switch DHCP snooping is enabled

DHCP snooping is configured on following VLANs:


DHCP snooping is operational on following VLANs:


Smartlog is configured on following VLANs:


Smartlog is operational on following VLANs:


DHCP snooping is configured on the following L3 Interfaces:

Insertion of option 82 is enabled

   circuit-id default format: vlan-mod-port

   remote-id: 0018.b9da.5300 (MAC)

Option 82 on untrusted port is not allowed

Verification of hwaddr field is enabled

Verification of giaddr field is enabled

DHCP snooping trust/rate is configured on the following Interfaces:



Interface          Trusted     Allow option     Rate limit (pps)

 --------------------   -------         ------------     ----------------  

Q1Which material is most helpful

Q2:which packets can help you find the cause


Customer just setup a IPv6 Network, with HSRPv6 on R1 & R2. After setting up, all hosts lose connection.

What would you recommend to your L1 Engineer as a Quick Fix?

CE1 key configuration

standby 1 priority 200

standby 1 preempt

ipv6 nd router-preference low

CE2 key configuration

standby 1 preempt

ipv6 nd router-preference high 



I think it is a rouge device because I don't see any problems with the HSRPv6 config. PCs are configured with "ipv6 enable", "ipv6 autoconfig"

The R1 have a "ipv6 nd-preference high" and R2 have "low" if I'm not wrong.


How fast fix the problem?


¡ Shutdown the link between CE2 and PE2.

¡ Shutdown the link between CE1 and PE1.

¡ Configure CE1 with highest HSRPv6 Priority.

¡ Configure CE2 with highest HSRPv6 pirority.

¡ Configure CE2 with low HSRPv6 priority.

¡ Shutdown CE1 interface e0/0.

¡ Shutdown PE2 interface e0/0.

¡ Disable fast-switching on CE's LAN.

¡ Enable fast-switching on CE's LAN.

¡ Change HSRPv1 to HSRPv2 version

CCIE Routing and Switching LAB Dumps

( 15 People are currently looking at this product )

Exam Code: CFG: LAB1、LAB1+、LAB2、LAB2+、LAB3
TS: TS1(5 sets)、TS2(3 sets)
DIAG:DIAG 1~DIAG 8(8 sets)

Certification Provider: Cisco

Certification Exam Name:CCIE Routing and Switching Lab

Update Date: Aug 08,2022

Free Cisco Written Dumps
For Top 50 Purchases
Latest Dumps
Numbers of Question & Answers

ccie lab uk

Here is the most accurate CISCO CCIE WRITTEN exam questions and answers. All study materials need to be carefully selected by professional certification experts to ensure that you spend the least amount of money, time, and pass the high quality exam. There is also a professional service team that can customize your study plan for you to answer all your questions, PASSHOT's CCIE Written Dumps is definitely the biggest boost for you to test CCIE that helping you pass any Cisco exam at one time.

    ccie lab uk

  • 557 Reviews
  • Those hosts can be predetermined feed line N A T   Fix: Reconfigured, also repeated s version /no s version, or not. In the end, I was courageous and reloaded R17 directly. Now I think it is terrible. Restart the card for nearly 4 minutes, but fortunately dm*** is fine. Finally, don't continue to do it, give up directly! * Confirmed various configurations,ccie lab uk, IGP, NAT, SW3/SW4 track has not been restored! Especially pay attention! ! ————The last thing is to pick up the sleeves and do it! ! ! Three ways for IPV6 terminals to obtain addresses: a) Unicast unicast A(config-if)#ip rip authentication mode md5   2. Enable RIPng protocol ipv6 router rip xxx (process name) Troubleshooting AAA for Management Access Ip routing vol 1, LAN SWITCHING, Internet Architeche. LAN at the time Or default to: cisco2-C2600 Supporting Other Layer 5 to Layer 7 Applications The second stage: DIAG can't end early, so I meditate (rest) there for about 17 minutes. Ten years of life and death, knocking on the version, to dawn. Thousands of orders, troulbe is hiding everywhere. How much more about the feature, nausea and stagnation. V1V2 turns, every day, every night, CCIE, pass busy 2. Switch to bridge the number of segments ( ports ) have the number of collision domains .   On the day of the exam, I always felt that I was nervous, but the fact is not what I thought. My mentality is very good. At 8.40 on October 31, I arrived at the Yintai Center and waited for nearly 30 minutes. The examiner finally came down with us. After entering the examination room, after a routine explanation, I started the exam. When I was troubleshooting, I was very excited. I met it. After the test took 1 hour and 30 minutes, all the questions were already After the inspection, I was also happy, but in the last 10 minutes, I pinged my multicast receiver. All the points were all a bit. I was a little panicked at the time. I was really anxious at that time. It was 1 minute and 120 minutes. I watched the countdown and there were 5 minutes. I started to check it from the right side and found that the configuration of the rp of a device was gone. I don’t know if the examiner gave me a mistake or a strange phenomenon. The last 3 minutes, finally, I just saved, time is up.

Have any question for us?

Cisco Dumps Popular Search:

ccnp tshoot practice labs gns3 ccnp tshoot cheat sheet ccna syllabus 2016 pdf ccnp 300-115 syllabus pdf ccnp route exam cost in india ccie security syllabus exam braindumps ccna test preparation ccie security virtual lab ccie mobile lab cost

Copyright © 2022 PASSHOT All rights reserved.