Problem:Server 1 can not get ip address.
Materials:
SW3#show ip dhcp snooping
Switch DHCP snooping is enabled
DHCP snooping is configured on following VLANs:
none
DHCP snooping is operational on following VLANs:
none
Smartlog is configured on following VLANs:
none
Smartlog is operational on following VLANs:
none
DHCP snooping is configured on the following L3 Interfaces:
Insertion of option 82 is enabled
circuit-id default format: vlan-mod-port
remote-id: 0018.b9da.5300 (MAC)
Option 82 on untrusted port is not allowed
Verification of hwaddr field is enabled
Verification of giaddr field is enabled
DHCP snooping trust/rate is configured on the following Interfaces:
Interface Trusted Allow option Rate limit (pps)
-------------------- ------- ------------ ----------------
Q1:Which material is most helpful
Q2:which packets can help you find the cause
Customer just setup a IPv6 Network, with HSRPv6 on R1 & R2. After setting up, all hosts lose connection.
What would you recommend to your L1 Engineer as a Quick Fix?
CE1 key configuration
standby 1 priority 200
standby 1 preempt
ipv6 nd router-preference low
CE2 key configuration
standby 1 preempt
ipv6 nd router-preference high
I think it is a rouge device because I don't see any problems with the HSRPv6 config. PCs are configured with "ipv6 enable", "ipv6 autoconfig"
The R1 have a "ipv6 nd-preference high" and R2 have "low" if I'm not wrong.
How fast fix the problem?
¡ Shutdown the link between CE2 and PE2.
¡ Shutdown the link between CE1 and PE1.
¡ Configure CE1 with highest HSRPv6 Priority.
¡ Configure CE2 with highest HSRPv6 pirority.
¡ Configure CE2 with low HSRPv6 priority.
¡ Shutdown CE1 interface e0/0.
¡ Shutdown PE2 interface e0/0.
¡ Disable fast-switching on CE's LAN.
¡ Enable fast-switching on CE's LAN.
¡ Change HSRPv1 to HSRPv2 version
Here is the most accurate CISCO CCIE WRITTEN exam questions and answers. All study materials need to be carefully selected by professional certification experts to ensure that you spend the least amount of money, time, and pass the high quality exam. There is also a professional service team that can customize your study plan for you to answer all your questions, PASSHOT's CCIE Written Dumps is definitely the biggest boost for you to test CCIE that helping you pass any Cisco exam at one time.
Exam Code: CFG: LAB1、LAB1+、LAB2、LAB2+、LAB3
TS: TS1(5 sets)、TS2(3 sets)
DIAG:DIAG 1~DIAG 8(8 sets)
Certification Provider: Cisco
Certification Exam Name:CCIE Routing and Switching Lab
Update Date: Apr 18,2024
=========================================================== ===================== a teacher answers all the questions of the students, he will harm the Lesson 1: Configuring Cisco ASA Adaptive Security Appliance NAT Features Modify the startup configuration key IPV6 supports abbreviated rules: Point out specific neighbors NA: Source IP 2001::2 Destination IP FF02::1:FF00:0001 19. How is the QoS of the backbone network deployed? What do you think is the backbone network when there is congestion? 7.Full Load rom after netboot fails Enter into slot 0 of the number is 1 Ethernet port Interfaces that are blocked will not receive / send user data . What are the characteristics and advantages of IPV6 compared to IPV4? Therefore, I think the value of the programmer is definitely not the technology itself, but the ability to make good use and good-looking software. 1) The root port does not participate in the competition of the specified port The first common method step: Q: What impact does achieving multiple CCIE qualifications have on your professional accomplishments? Let’s talk about this picture. First of all, I agree with a few points: 1 Detect the validity of the interface Let’s talk about this picture. First of all, I agree with a few points: 6. Opportunities and platforms A section of configuration: R14(config-if)#ppp chap password 16300 Interface Serial1 Enable B(config)#access-list 1 permit any The PC obtains the 64-bit prefix and then uses the EUI-64 format to generate the port ID based on the MAC. and opening my own computer company. There Rommon5>DEFAULT_GATEWAY=10.10.22.2 (default gateway, is the address of the PC Boot: image specified by the boot system commands => All neighbors Rommon8>Sync (Save Parameter Configuration) =========================================================== =============== 3. The twisted pair transmission distance is 100 meters . RIPng 2. Connector type : BNC interface , AUI interface , RJ45 interface , SC/ST interface RIPng =========================================================== =============== again, then one by one,ccie routing and switching lab fee, every time Taking the cisco e-learning From On the day of the exam, I always felt that I was nervous, but the fact is not what I thought. My mentality is very good. At 8.40 on October 31, I arrived at the Yintai Center and waited for nearly 30 minutes. The examiner finally came down with us. After entering the examination room, after a routine explanation, I started the exam. When I was troubleshooting, I was very excited. I met it. After the test took 1 hour and 30 minutes, all the questions were already After the inspection, I was also happy, but in the last 10 minutes, I pinged my multicast receiver. All the points were all a bit. I was a little panicked at the time. I was really anxious at that time. It was 1 minute and 120 minutes. I watched the countdown and there were 5 minutes. I started to check it from the right side and found that the configuration of the rp of a device was gone. I don’t know if the examiner gave me a mistake or a strange phenomenon. The last 3 minutes, finally, I just saved, time is up.
Cisco Dumps Popular Search:
ccnp tshoot 300-135 quick reference pdf ccnp route topics ccnp tshoot exam topics ccna dumps 9tut ccie lab setup watson ccna what is the latest ccna exam best ccie security training in india ccnp tshoot dumps vce ccna vce dumps
Copyright © 2024 PASSHOT All rights reserved.