ccnp tshoot 300-135 multiple choice questions

ccnp tshoot 300-135 multiple choice questions

? Fast Switching Optional delivery to simplify the execution of routing policies access-list 1 deny 172.16.32.0 0.0.0.255 In fact, this is more a problem, because such an approach, in fact, the last 8 bit group no matter what, will be live match, he is even more imprecise. ? Core switch configuration: Add all Route-map COST2 permit 10 match ip address prefix-list 100 set extcommunity cost 1 5 General BGP routers do not accept containing its own AS routing information number, but can neighbor routing sources neighbors allowas-in a few of my as numbers , to make an exception. By the original impact of routing attributes The default is shutdown , optional protect , restrict It is recognized that the attribute must be followed to describe the next hop router to the destination. In the one local BGP routes advertised to EBGP the Peer time, whether they carry MED values , need to be determined under the following conditions ( not EBGP Multi-hop EBGP RIPv2 8 bits That is, a site address, the MAC address, is reserved at this level to identify the only site on the network. Vlan 10 ? Fa0/20 Preemption enabled, min delay 30 sec BGP does not update the route periodically. It is updated only when needed. Because the route of the public network may be turbulent, there will be a certain waiting time for triggering the update. The IBGP peer is 5S . The EBGP peer is 30S . During the time, BGP can still collect routing information, so BGP convergence will be slower. But there is a loop in the second floor environment. 192.1.168.2 3 0003.47d9.c8f1 2BB648AB interface-id 584a38f0 END A route-map containing a set of match statements can be defined in advance as a list of commands called a policy-list. Network 100.0.1.0 mask 255.255.255.0 Backup port: Discard status. A backup of a specified port occurs when a switch has two ports connected to the same shared medium. AS_SEQUENCE exactly the same, except that the list of AS numbers belong to the local Federation AS Port-security supports 802.1Q tunnel interface Field name B and C receive this better BPDU and continue to flood the network. BGP routing table entry for 172.16.0.0/16, version 4 Load balancing: round-robin Group members: On Route . 1 : the AS_PATH : 100 the MED : 200 is External RouterID : 1.1.1.1 BGP routing table entry for 1.1.1.0/24, version 2 Route-map Learn ? None The 10.1.10.0/25 subnet cannot be updated because the subnet and the update source interface belong to the same main class network, but the masks are different. Double-point bidirectional routing re-issuing problems 92 Ip arp inspection validate { [dst-mac] [ip] [src-mac] } Maximum MAC Addresses : 1 !! The maximum number of secure addresses, the default is 1 9.9.12.0 is directly connected, FastEthernet0/0 100 i Route-map RP permit 10 match policy-list as100 HOLDTIME CISCO defaults to 180s ( 3 times KEEPLIVE timer ), which is included in the open message. RFC1721 R3 's loopback interface IP has been declared into OSPF , and R4 learns loopback routing through OSPF . Therefore, the BGP table for R4 is as follows: Start a TC while timer for the root port and all non-edge designated ports . The timer value is equal to 2 times the hello-time timer. Enhanced Interior Gateway Routing Protocol (EIGRP) Open Shortest Path First (OSPF) Sw(config-if)#switchport mode private-vlan host The associated PC service, that is , the data frame whose source is the MAC , can enter the interface. 100 Ip sla monitor responder The DA 40bit multicast address is used to indicate that this FRAME is an ISL . Used in route-map , when some of the matching entry, and using the set command, the route-map used in a neighbor (e.g., out time direction), then to update the route to a neighbor, the BGP of MED properties will Inherit the metric value of these routes in the local IGP Bgp confederation identifier 345 bgp confederation peers 64512 neighbor 4.4.4.4 remote-as 64512 Paths: (2 available, best # 2, table Default-IP-Routing-Table) Flag: 0x820 Use set as-path tag to restore, for example, this example on R3 , Use ip community-list to match the community value R1 uses 1.1.1.1 as the update source, trying to establish a BGP connection with 2.2.2.2 , and the local IP address of R2 is 1.1.1.1 , and Metric Circuit-ID type Show ip bgp dampening The above command calls the defined policy-list in the route-map ; multiple policy-lists can be called in a route-map . Within the federation, both R3 and R4 belong to AS64512 . For R4 ( AS64512 ), R5 belongs to AS64513 , but for the federal outside, R3R4R4 is AS345 , and external extremities do not know that AS64512 and 64513 exist. 2 The configuration of SW2 is as follows: As we R3 on the RIP routes injected into OSPF marked the Tag 1111 , then the next The switch configured with Uplinkfast needs to be a stub switch or an access layer switch in the network three-layer structure. It cannot be the root bridge. If R1 turns off auto-summary and network 1.1.1.0 mask 255.255.255.0 , then R2 can learn BGP route 1.1.1.0/24 Routing Policy Ip dhcp snooping trust Configure the secure address of each interface ( Secure MAC Address ) If there is a class route lookup ( no ip classless and ip cef is off ), when receiving a data packet, the router first searches for the main class to which the destination address belongs. If there is a main class route in the routing table, then the subnet is searched. If there is a subnet route,ccnp tshoot 300-135 multiple choice questions, the query is limited to these subnets and further searched. If the final lookup fails (no subnet matches this route), the packet is dropped even if there is a default route; if there is no local For the main class route, see if there is a default route. If there is, then it will be forwarded by default route. If not, the packet will be discarded.