ccie r&s lab workbook

ccie r&s lab workbook

　　 15s   　　analysis Show sessions to view " I " telnet outgoing sessions   Router ospf 1   Ppp authentication CHAP   　　 IPV6 - R - IPV4 - R - IPV6 dual stack router 5.ISATAP P2MP site Ip route (Destnation Network IP) (NetMask) [NextHopIP | LocalInterface]   the ability to think independently and loses the ability to solve 3 . Week when the period of notice   FRAME-REL A Y is a non-broadcast multi-access type network that does not support broadcasting.   　　Even if you have tested the CCIE for routing and switching, you may not be able to do the right thing. ** Troubleshooting section: ** 　　6. MPLS L3 ***, what if I want two different *** to be one-way visits? Configuring and Verifying Active/Standby Failover 　　15. Can BGP achieve load balancing? If so, what are the methods? =========================================================== ===============   What are the differences between OSPFv3 and OSPFv2? Spanning trees can avoid loop problems caused by redundancy . Solving the problem : put redundant ports into blocking state .   IPV6 Boot: image specified by the boot system commands Static: ipv6 route 2002::/64 serial 1/0 (next hop address) (3) Telecom operators Rommon 1 > confreg B(config)#inte s 0   First, there are brothers introduced, put the key equipment on the display, in fact, this is no way, because his putty is not cascading,ccie r&s lab workbook, so how many windows you have ordered you do not know. When all the configuration is complete, put the key equipment in the lower part of the display and check it in five minutes! ! Avoid being TR and don't know. 3. Port number : Provides the session layer to distinguish data without application . Identity service .   2. Set the dialed number   In practical applications , cisco hdlc incompatible tolerance standard hdlc.   Show hosts   C: 192.168.0.0/24 -- 192.168.255.0/24   6:50 AM Departure End   The Ram : random access memory , power failure information is lost <-- currently effective configuration <-- running-config    Clear cdp table   2. Version 3 (multicast lo0) takes out IGP establishment and examination of the sp lab is a process from scratch. 3. IPV6 packet structure is simpler and the forwarding efficiency is higher. itself can not mean that you have any value, a pass and a fail are not Default Settings ( default configuration ) file , a switch for initialization . To ensure the normal operation of the switch .2.CISCO Router   Ip ospf x area x ------------------------------------------------   　　 　　21. What is the mechanism for processing the loop between the L3 network and the L2 network? =========================================================== ================   Configuring and Verifying Other Basic Access Controls Terminal history size <0-256>   　　3. What are the main advantages of the TCP/IP modular design? the exam. I left the company on July 15. When I arrived at my wife's home in Kunming, I had to self-study for a month to prove my ability in the cisco experiment. This Have a link state database ( network map )   2. Tunnel technology IPV6 communication between IPV6 networks (main), IPV6 communication between IPV4 networks Can not be deleted .   Change the interface mode to trunk working mode   CD several times, and drilled on the spot, only encountered a little 2. In the back door of your living room, there is an iron gate (s1 of B). Although the thief enters your living room, you still can't go out from the back door to your treasury (C). EIGRP Automatic generation of EUI-64 format (standard 64-bit) A: 10.0.0.0/8   1. Connect to a service . 2. Connect based on virtual link   　　 Pass through the NCP can support multiple network layer protocols via through LCP can be achieved " Authentication ", " compressing ", " error detection   Worldwide unicast address: similar to the public address in IPV4, mainly used in the global Internet Autonomous system :   Configure a virtual loopback interface . The loopback interface is in the UP state by default .   Serial1 is up, line protocol is up   Ipv6 router ospf 1 Permit   Interface serial 0   Tone test igrp event content   is the pressure of learning, I can't use words to convey this pressure Password cisco   Password cisco   　　 I have never given the readers of the blog a good analysis of how I went to the technical staff. Today I am going to take a dim sum and simply talk about how I got on the technical line. I think it’s a little weird to think about it. There are still some small touches. =========================================================== ===============   Router ospf 1   Save current configuration   Configure this switch to be in server mode [server|client |transparent]   My again, then one by one, every time Taking Config-register 0x2142   No shut   Configuration with multipoint subinterface   2. The data link layer : data error detection , physically address MAC   End   =========================================================== ==============   Show controllers serial 0   OSPFv2 processes IP subnets, and OSPFv3 processes links. The 16-bit IPV6 multicast address header has a special meaning: the last 112 bits are generally called group id. CISCO router , the serial interface default adopted by cisco HDLC encapsulation   Lesson 1: Defining the Cisco ASA Adaptive Security Appliance MPF 　　UDP (User Datagram Protocol): An unreliable, connectionless protocol in the transport layer. Configuring and Verifying FTP Inspection Rip V1 uses broadcast announcement broadcast address : 255.255.255.255    Hostname   ! In OSPFv2, only the primary IP of a port can participate in the OSPF protocol. (2) Related industry manufacturers Rip management distance : 120   external conditions are second, or a sentence, do you have the pressure Network administrators manually define (how many random) The router of the DCE needs to configure the clock frequency.   ability to solve problems. Even after I finish the exam, I can only Frame-relay map ip 10.1.1.2 110 broadcast for manual static mapping    1111 1110 10 54 0 EUI-64 automatically generated port ID my work. Proud for a while. With 0x0 means that router to enter into the Rom monitor mode   Ip address 1.1.1.1 255.0.0.0   Displays the current outside the TELNET session   　　6. Opportunities and platforms Send local password in CHAP mode   Into Fast Ethernet Wang 0/1 Interface   /48 NLA next level polymerization R14(config-if)#ip address negotiated   In the IPV6 transition technology: there are 5 types of tunnels See all the EIGRP best route ( stored in the routing table )   　　23. What is the spanning tree mode of the 3550? What is the number of spanning trees? Multicast routing function: ipv6 multicast-routing 　　Internet layer: Provides hardware-independent logical addresses that allow data to be transferred between subnets of different physical structures. Provide routing functions to reduce traffic and support data transfer between networks (the term "internetwork" refers to a large network formed by multiple Internet connections, such as a large company's network or the Internet). The conversion of the physical address (the address used by the network access layer) and the logical address is implemented.