ccnp route passleader

ccnp route passleader

Manually shut down a specific port and then noshutdown Address family Enabling BPDU filtering on an interface is the same as disabling spanning tree on it and can result in spanning-tree loops. The configuration of SW2 is as follows: Using ICMP protocol to detect 10.1.1.2 reachability (source address 10.1.1.1 to ping10.1.1.2 ) Track Object 's ID is 1 , associated to ip sla monitor 1 Sh ip bgp neighbors {address} advertised-routes Atomic_Aggregate and aggregator // 100: 200 indicates that this is for the AS200 's BGP re-released to IGP Ip prefix-list huizong permit 172.16.0.0/16 ip prefix-list mingxi permit 172.16.1.0/24 ip prefix-list xiayitiao permit 10.1.24.4/32 route-map RP_mingxi permit 10 Redis static route-map cisco Switchport mode private-vlan host R1(config-router)#redistribute rip subnets tag ? Difficult case 60 About the rate_in_pps parameter: This route was therefore sent to R1 . The BGP election routeriID rule is the same as OSPF . BGP state machine Next hop 10.1.12.2, FastEthernet0/0 valid adjacency BEGIN Hello time 3 sec, hold time 10 sec Next hello sent in 1.280 secs Planning Principles / / Use the federal member AS number to establish BGP * i Neighbor 4.4.4.4 update-source Loopback0 neighbor 10.1.25.2 remote-as 200 Ip sla monitor responder Bridge ID Neighbor 1.1.1.1 update-source Loopback0 The next-hop attribute can be changed by next-hop-self In R1 the ip route 0.0.0.0 0.0.0.0 null 0 then re-released in a static routing process, but also to In this step, we run the BGP protocol on the above basis to complete the establishment of basic BGP neighbor relationships: Redistribute rip metric 10 subnets distribute-list 1 out rip FastEthernet1/0 Router bgp 100 ( Well-known discretionary ) If you want to delete multiple communities (not all), you can write multiple items in one community-list , such as Path Then IOS will automatically change the command to Set ip next-hop ip1 ip2 ...... Y Set the interface to DTP dynamic negotiation, optional auto or desirable Obviously, the DHCP server is aware of the above problem, and the action it takes is to ignore this DHCP request. Therefore the PC cannot get the address. 100 Passive-interface Route-refresh The configuration of SW1 is as follows: 200 i Ip default-network 192.168.1.0 5.5.5.5 Router(config-router)# Redistribution between different OSPF processes Device ID 8.3.4 Questions 104 Regular expression ? RIP Version 2 Protocol Applicability Statement DHCP relay Paths: (2 available, best # 2, table Default-IP-Routing-Table) Flag: 0x820 R3 FastEthernet1/0 EIGRP please see the passhot of EIGRP notes on black passhot(visit passhot.com ) If the router accepts the parameters of the neighbor in the OPEN message, it will answer a keeplive message, and send the message for the period of 1/3 of the holdtime (but not less than 1S ). CISCO defaults to 60S . If the hold time is 0 after negotiation , the keepalive keep-alive message is not sent . In this way, whether the method of re-publishing the static summary route or the method of distributing the list filtering route can ensure that the network is not interrupted in the event of a network failure, as follows: It means for VLAN100 traffic, not to log the ARP ACL discarded packets match Switchport port-security maximum 1 Static routes Layer 2 switching *>i *>i100.0.2.0/24 300 Ip prefix-list 1 permit 172.16.1.0/24 ip prefix-list 1 permit 172.16.2.0/24 route-map test permit 10 4.3.1 improvements 35 Next, we SW2 on the vlan10 port removed, directly in fa0 / 2 on the no switchport access vlan The possible values ​​for the first column are as follows: OSPF 's neighbor command is not the same as EIGRP . After testing, in the Ethernet environment, directly refer to the neighbor , and still send multicast hello. The process of processing a VLAN frame by a trunk port is as follows: IP address About route reflection clusters Ip address 192.168.100.254 255.255.255.0 B is passed to its IBGP neighbor C (doing a reflector), then on C , the route NEXT_HOP is still the A router (update source IP ) BGP configuration Match 100 , 1400 , 300 400, etc. RIPng or OR2 , SW1 , and SW2 run OSPF , and OR2 acts as the egress router of the telecommunications, injecting a default route into the OSPF domain. OR1 will be local Reduce network migration time without disconnecting existing connections, and do not need to change device BGP configuration in large batches Access-list 1 permit 192.168.12.0 router rip The identifier of the authentication item indicates that the entire routing packet needs to be verified. RFC1771 A Border Gateway Protocol 4 Ip route 172.16.1.32 255.255.255.224 192.168.23.3 Switch(config-if)# no shutdown Per packet load-sharing is disabled IP unicast RPF check is disabled Inbound access list is not set Outbound access list is not set The same prefix is ​​obtained through different protocols, first than AD , and later than metric The address of the slave is the optimal next hop address. Then in each sequence, we can define two elements for policy deployment: matching conditions, performing actions . You can define multiple conditions, and when the conditions are matched,ccnp route passleader, they will perform the relevant actions specified by the set . Slightly mention here, the set statement is not necessary, for example, if the route-map is only to match the traffic of interest, then there may be only a match statement and no set statement.