ccnp route 6.0 instructor lab manual

ccnp route 6.0 instructor lab manual

There are classes and classless route lookup mode After PK , there is no doubt that the default route pointing to telecommunications appears in the routing table, and points to the default route of the education network, "wacky" to hide. When the default route to the telecom is invalid, it disappears from the routing table. At this time, the default route to the education network is "floated". Policy-list feature Although the network devices are in the same subnet, they belong to different pVlans , and communication between pVlans must be implemented through the default gateway. Router(config-dhcp)#default-router [host address] * i100.0.2.0/24 As the next hop to 100.0.1.0 and 2.0 . In the R4 on 1-4094 Configured MAC Addresses : 0 !! Manually configured secure MAC address, not here Bindings are just special address pools. There is no limit on the number of manual bindings, but you can only configure one manual binding per host pool. In 802.1D , the TYPE field uses only the highest and lowest bits to indicate TC and TC acknowledgment, and RSTP extends this field: Configuration case Difficult case 60 LocPrf 100 i Route 11.11.11.0 is introduced on R1 . Passive: passively wait for other side to ask Double-point bidirectional routing re-issuing problems 92 DMZ-Link Bw 193 kbytes Policy accounting is enabled on an input interface, and counters based on parameters such as community list, autonomous system number, or autonomous system path are assigned to identify the IP traffic. Routing, then: !! ISP1 , ISP2 and GW all need to open CDP 200 i Another recommended solution is to adjust the management distance of the routing protocol: Match, and the result is that there is no match, it is directly discarded, regardless of whether there is a valid entry in the DHCP Snooping database . Experimental phenomena: ! Generally done at the AS boundary, tell yourself the local-pref value from within AS . Port-Security and Sticky MAC Address RIPng for IPv6 After a few seconds,ccnp route 6.0 instructor lab manual, D receive this the BPDU , Block out port P1 2.2.2.2 VTP Version capable 1 The simple horizontally separated rule is that the update message sent from an interface does not contain the network contained in the update received from the interface. In other words, the route I received from this interface will not be from this interface. Send it back. Match ip route-source Bytes Neighbor authentication Redirection enabled, 597.032 sec remaining (maximum 600 sec) Time to live: 14397.032 sec (maximum 14400 sec) Port ID of the BPDU sending bridge (priority + port number) ! R4#sh ip ro 192.168.1.0 OSPF redistributes into BGP ORIGINATOR_ID and CLUSTER_LIST In addition to matching 100 to 106 outside the AS_PATH BGP routing table entry for 100.100.100.0/24, version 3 Paths: (2 available, best #1, table Default-IP-Routing-Table) Multipath: eBGP Match ip address 2 set metric 3 The next hop of the route advertised by the device is 0.0.0.0) Metric Basic VLAN communication principle Ip dhcp snooping information option allow-untrusted s suppressed routing entries, such as doing route summarization, suppressing details The configuration of R1 is as follows: CODE : 82 Redistribute static subnets Next, we SW2 on the vlan10 port removed, directly in fa0 / 2 on the no switchport access vlan RIP-1 only sends RIPv1 updates Acl-match none —Does not log packets that match ACLs. ^\(65000\)$ Related commands : ? One-arm routing Community value (route), then how to write it? If you directly match no-export , it will match with 11.11.11.0 , so you should use the exact-match keyword. If configured on R3 as follows: Modify the TAG of the summary LSA of the ASBR notification ... For example, change the COMM value of a route of AS12 to 10000 , and the RFC uses hexadecimal to indicate the COMMUNITY attribute, while CISCO VTP Operating Mode : Server Maximum VLANs supported locally 1005 Router eigrp 100 Neighbor 10.1.23.3 local-as 201 Ip as-path access-list 1 permit _1$ A sends the BPDU out of its designated port, and the BPDU is flooded to the network. All VLANs Site-level site identification: Identify the various sites on the network at the data link layer. Therefore, when the route lookup mode of the router is classless or the classless route lookup mode, the default lookup action of the router is the longest match criterion. For example, in the above figure, when R3 receives a packet and goes to 172.16.1.1 , then in fact, 172.16.1.1 is "dropped" in the network of 172.16.1.0/24 and 172.16.0.0/16 , both seemingly Yes , but 172.16.1.0/24 obviously has a longer match, so the packet is eventually dropped to R1 . Similarly, if there is a data packet going to 172.16.2.1 ? Since the entry of 172.16.2.0/24 is the highest according to the longest match principle, the data is thrown to R2 .