ccnp tshoot instructor lab manual pdf

ccnp tshoot instructor lab manual pdf

Match community 11 Redistribute connected route-map test <1-99> Community list number (standard) So match interface is a match with the outbound interface attribute, and this * i100.0.1.0/24 aggregate-address 192.168.0.0 255.255.0.0 as-set after, R1 can only learn to 2.0 , the summary route are rejected, the reason is 1.0 carries no-adver of Community Community , when the summary route plus the as-set keyword after Will inherit its community , so the summary route also carries no-adver , this time Reposted FAQ 49 The non- root bridge receives the TCN on its designated port 0 ? In R1 the ip route 0.0.0.0 0.0.0.0 null 0 then re-released in a static routing process, but also to Access-list 1 permit any route-map PBR permit 10 match ip address 1 Link aggregation mode supplement: 100 After receiving the BPDU packet, the interface will immediately switch to the err-disable state. Path Static routes meaning Switch(config)# vlan 10 Metric =0 VLAN Interface Route-map The process learns the external route, so the update source here is R2 . * 10.1.12.1, from 10.1.12.1, 00:07:30 ago PVLAN considerations For example, to fetch the 192.168.1.0/24 route, access-list 100 permit ip 192.168.1.0 0.0.0.0 255.255.255.0 At this time, actually R1 's loopback port to R2 needs at least 2 hops, then this time you need to configure both neighbor xxxx ebgp-mul 2 R1#sh ip b Route tag 9 Routing? AS_SET : A list of unordered AS numbers on a path to a particular destination Sign In direction New link Link1 between A and Root PS : It should be noted that there will be class and classless route lookup methods, which are distinguished from classful and classless routing protocols. 3.3.3.3 If you increase the switchport port-security aging static command, the aging time of the statically configured secure address also starts. Then, first R2's own routing table will change, 3.0 routing is filtered out, and R3 is the downstream RIP router, 3.0 can not learn. About the prefix list There are classes and classless route lookup mode Port number 520 Look at the above picture, the gray space 172.16.0.0/16 , this network number, we call the main class network number , the so-called main class network number, meaning the network number, according to the IP address category to which it belongs , corresponding to The network number obtained after the default subnet mask length. Such as 172.16.0.0 this is a 201 200 100 Then look at the R4 's BGP table: Connect Router bgp 345 Ip route 172.16.1.32 255.255.255.224 192.168.23.3 Sign 159 220 , 91 70 200 201 300 Multicast capability An important improvement in RSTP is the rapid transition of ports. The traditional STP algorithm needs to go through several timers before transitioning an interface to the forwarding state. In order to get a fast convergence of the network, we may adjust the timer, but this method may affect the stability of the network. When a data frame is sent from the Hybrid port, the switch determines whether the attribute of the VLAN on the port is Untag or Tag . If it is Untag , first strip the VLAN tag of the frame and then send it ; if it is a Tag , send the frame directly. OSPF routing: including 3.3.3.0 , and the direct connection network segment 192.168.23.0/24 declared into OSPF is injected into the EIGRP process. This R1 Promiscuous Management distance ( Administrative Distance , referred to as the AD ) The interface will not send BPDUs , and will also ignore received BPDUs. Policy-based routing is more powerful and flexible than traditional routing. It allows network managers to select forwarding paths based on destination addresses and packet types, packet sizes, applications, or IP source addresses. inQ number of messages waiting to be processed from this neighbor Not advertised to any peer Local If there is a tag , it is determined whether the trunk port allows the VLAN frame to enter. Allow the next step, otherwise discard the frame. Ip prefix-list 1 seq 5 permit 100.0.1.0/24 ip prefix-list 2 seq 5 permit 100.0.2.0/24 route-map test permit 10 Finally note: None Dialer Dialer interface Bgp default local-preference 500 // Modify the default lp value of the route originating locally In this step, we run the BGP protocol on the above basis to complete the establishment of basic BGP neighbor relationships: Application example Policy-list * i100.0.1.0/24 [Experiment 3 ] No main class network; there is a default route, take the default route / / Used to match the BGP neighbors passed to my summary route , here is the IP of R4 : Disabled BGP is designed to AS transfer routes between, so it is actually a hop AS . Router bgp 64513 no synchronization Network 192.168.24.2 0.0.0.0 area 0 Route-map test deny 10 match tag 1111 In the above figure, the configuration revision number of server and client is the same, but the vlan information is different. At this time, an error will be reported, prompting md5 digest checksum mismatch Topology change mechanism The configuration of R3 is as follows: Then there is a problem. After the device goes online, what if we want to change the configuration of the device and manage these switches? Is it necessary to take a laptop with a console cable down to the machine room for on-site debugging? This method of twisting is completely unreasonable, right, it can be managed remotely by telnet or other means. On the router telnet we are very familiar with,ccnp tshoot instructor lab manual pdf, as long as three up, you can telnet to the router, then it follows that we take a look at how to manage the switch.