ccnp 300-115 lab questions

ccnp 300-115 lab questions

Two-point two-way routes redistributed problems 200 ? In the BGP table, only one route is preferred, which should be R3 (because R3 's RouterID3.3.3.3 is less than R5 's 5.5.5.5 ) 100$|400$ Protocol Interface The routing between the internal LOOPBACK of the AS can be learned separately. Both R1 and R3 update the route of the 100 network segment to R2 . Without any policy, the BGP routing rule will always be compared to the RID , and finally the route of R1 is preferred . 100 Ip route 10.1.1.0 255.255.255.0 10.1.254.1 The above command means to inject the detail route defined in map1 in the local BGP RIB when the summary route matched by map2 is normal . When the summary route hangs, this detail disappears. This is called conditional injection . Below we look at the details of these two route-map , these need to pay special attention. AFI (Address family identifier) For experiments on specific Layer 3 switch management VLANs , see the CCNA Lab Manual By passhot. 2 Vlans in spanning tree forwarding state and not pruned Ip address 192.168.100.254 255.255.255.0 When the number of prefixes received from the neighbor exceeds the maximum number 300 of 90% (default 75% ), generating a message log There are 2 forwarders (1 active) Ip arp inspection validate { [dst-mac] [ip] [src-mac] } Note that the above two configurations are invalid for manually configuring the secure address of switchport port-security mac-address 00b0.9999.9999 . That is, the static security address entry configured by the above method never times out. For example, on a PC , statically bind the gateway IP and the MAC of the gateway with arp-s to prevent arp spoofing, or use the command arp for binding on the network devices of the key nodes . Information, so that ISP1 is hanging, so the data of the PC accessing the 100 network is switched to ISP2 , and the network is constantly Neighbor 4.4.4.4 remote-as 345 OSPF and OSPF If you configure the following, then the COST comparison will exceed the weight and become the most preferred comparison rule. Major Points The route works,ccnp 300-115 lab questions, but it is basically not used now, because the uncertainty is too strong) 1 Network 100.0.1.0 mask 255.255.255.0 About the rate_in_pps parameter: Port-Security secure address: secure MAC address When R2 One way is to establish a fully interconnected IBGP Sw(config)#vlan 201 Here, because there is an OSPF interval , and OSPF does not know BGP , the BGP attributes will be lost during the re-release process . Interface fast0/1 Access-list 1 permit 192.168.12.0 router rip Bgp cluster-id 222.222.222.222 Activate Port-Security (on the access interface) 100 When the RR receives a route from an EBGP neighbor and passes it to the client or non- client , CLUSTER_LIST is not created . Timers 29 * 200 i If both commands are closed: Discard the illegal ARP packet, the switch will discard the illegal ARP after log Policy-list feature Neighbor 10.1.35.5 unsuppress-map unsupp RIP redistribute default route If there are no dynamic and static routes on R2 , and the configuration is as follows: In the port field of the circuit-ID suboption, the port numbers start at 3. That is to say, in this field, the port number is from 3 , the first port number is 3 , and so on. For example, a 24- port switch with an SFP slot , port3 is fast x/0/1 , port4 is fast x/0/2 , and so on, port 27 is the x/0/1 port of the sfq module . Where x is the stack member number. 10.0.0.0/24 is subnetted, 1 subnets : ccnp 200 3.3.3.3 ( metric 101 ) from 3.3.3.3 (3.3.3.3) Auto: passively wait for other side to ask R2(config-router)# distribute-list 1 out The GW configuration is as follows: Used to advertise available routes, revoked routes, or both, 200 Bridge using these 4 steps to save each port received the " best " of the BPDU a copy. When each BPDU arrives, it will check according to this 4- step decision step to see if it has a better BPDU saved on the port . If it is, it will be updated. In R1 the ip route 0.0.0.0 0.0.0.0 null 0 then re-released in a static routing process, but also to Match abd , abcd , abcdefg, etc. Port Vlans in spanning tree forwarding state and not pruned switchport trunk encapsulation dot1q switchport mode trunk C BGP supports MD5 authentication. To enable MD5 authentication on the TCP connection between BGP peers , use the following command: The packet contains a maximum of 25 routing entries. Community: inherits the community of all detailed routes , forming a list ? 6 V1 uses broadcast, which is sent every 30s by default , using UDP port 520 (source, destination port) Note that community is not sent by default and must be send-community . Commands Not advertised to any peer Local On R1 , filter out 11.11.11.0/24 routes, other release .