ccnp route 300-101 exam questions and answers

ccnp route 300-101 exam questions and answers

R1(config-route-map)# match ip address prefix-list list1 Therefore, in fact, the ORF is a feature of the route-filtering by means of the prefix-list . The prefix-list is pushed locally to the peer to allow the peer to perform routing prefix filtering. Metric Distribute-list 1 out Different prefixes (network number + mask, indispensable), belonging to different routes in the routing table We restore the experimental environment to the basic configuration: BGP neighbor relationships are as follows Receiving behavior (2) By default, the routing entry of 1.0.0.0 updated by R1 is ignored. After configuring ip rip receive v 1 on S0, you can learn. Local origin This summary route generated locally is 172.16.0.0/16 , NH=0.0.0.0 , weight= default value 32768 , origin=i . The detail route is marked as " s " and is therefore suppressed. Set ip next-hop ip1 Set ip next-hop ip2 Neighbor 10.1.25.5 remote-as 345 no auto-summary 3.3.3.3 The src-mac detects the received ARP packet. The source MAC address of the Ethernet pillow is the same as the sender MAC address in the ARP body . This verification action is performed in both the ARP request and the response message. ... Ip helper-address 192.168.100.1 technical background case study There are class, classless routing protocol redistribute At this point, the direct connection is re-released on R2 , and it is found that 1.1.1.0 has not been re-released into RIP. Update it; however, it does not send its secondary address 11.0.0.0 segment from fast0/0 to R1 (unless the split horizon is turned off). Route Tag Bgp confederation identifier 345 neighbor 4.4.4.4 remote-as 64512 100.0.1.0 the BGP route, preferably up to R5 . //The default community is not sent, so this command must be configured BGP table on R7 : 5.5.5.5 Known via "bgp 200", distance 20, metric 0 Tag 13, type external 0 ? Bgp-policy accounting input Network ! Packets FastEthernet0/0 Switch(config)# vlan 10 OSPF 's neighbor command is not the same as EIGRP . After testing, in the Ethernet environment, directly refer to the neighbor , and still send multicast hello. ? 200 i Source of routing information: How is this route learned, for example, static, or through OSPF , IS-IS , 100 Router bgp 100 IP The configuration of the DHCP server is a general configuration and will not be described here. The Response packet contains a maximum of 25 routing entries. Router bgp asnumber When ISP1 is down,ccnp route 300-101 exam questions and answers, and the interface of GW connected to ISP1 is DOWN , the data of PC accessing 100 network is switched to ISP2. PVST+ has been improved in this respect. PerVLAN means that a VLAN corresponds to a spanning tree. In this way, the switch will calculate the spanning tree based on the VLAN . We can adjust the priority and other related parameters by using a separate VLAN spanning tree, thus affecting Spanning tree calculations ultimately achieve reasonable link bandwidth utilization. For example, in the above figure, there are two VLANs , 10 and 20 on the intranet . Let SW1 become the primary root of VLAN10 (the lowest priority of the whole network switch), SW2 becomes the secondary root of VLAN10 , and SW3 has the highest priority, so we will BLOCK off. SW3 is connected to the upper port of SW3 . In contrast, VLAN 20 is also the most specific adjustment. In this way, the user of VLAN 10 will go out to the left link, the user of VLAN 20 will go to the right, and the link is properly used to achieve load balancing.