Here is the most accurate CISCO CCIE WRITTEN exam questions and answers. All study materials need to be carefully selected by professional certification experts to ensure that you spend the least amount of money, time, and pass the high quality exam. There is also a professional service team that can customize your study plan for you to answer all your questions, PASSHOT's CCIE Written Dumps is definitely the biggest boost for you to test CCIE that helping you pass any Cisco exam at one time.
CCNA Routing & Switching Written Exam
Exam Number : 200-125 CCNA
Associated Certification : CCNA Routing & Switching
Duration : 75 minutes (55 - 65 questions)
Available Languages: English, Japanese
NOTE: This exam tests a candidate's knowledge and skills related to: Network fundamentals, LAN switching technologies, IPv4 and IPv6 routing technologies, WAN technologies, Infrastructure services, Infrastructure security, Infrastructure management.
Device Configuration To update the LSDB , the LSP will be cleared from the LSDB . After the old LSP is cleared from the LSDB , it will remain for a while. Ip address 10.1.56.5 255.255.255.0 0/0/0 Reservable Bandwidth[7]: Understand the establishment process of LDP neighbor relationships. Area Address: 49.0001 10.1.34.0/24 Mpls traffic-eng tunnels mpls label range 200 299 Nexthop 10.1.12.2 FastEthernet0/0 label 204 TCP connection: 3.3.3.3.41954 - 1.1.1.1.646 1230 I don't want L1-router to generate this default route, or more rigorously, we don't want L1\L2 router to press att , the method is Do not need to explain it again? At R4 , R4 pops the top label and forwards the packet to R5. Then, finally, the data is introduced into the established tunnel . In fact, after creating a TE tunnel on R1 ,cisco exam practice test, a local tunnel is in it. Message 0.1.123.2 *Aug 18 09:06:07.919: Setup Prio: 7, Holding Prio: 7 Mpls traffic-eng tunnels mpls ip Then shut down the e0/1 port of R2 : In the above figure, we define attribute tags for the two interfaces of R1 . The attribute tag attribute-flags is a 32-bit field. Next, you can test the forwarding of traffic on R1 . CSPF algorithm working mechanism R3.00-00 One goes from tunnel0 , cost=1000+1=1001 one goes from eth0/1 , cost=10+10+10+1=31 Comparison of terms between IS-IS and OSPF : Interface loopback0 In fact, this is a metric trick, but when we are thinking about it, remember to take the virtual path of the tunnel into consideration. RSVP-TE requests to establish an LSP tunnel according to the above path. The configuration of R2 is as follows (all configurations are omitted from the configuration of interface IP ): OSI has established standards for two network protocols for routing: ES-IS and IS-IS : Reservable Bandwidth[5]: 10.1.45.5 5.5.5.5 Uptime: 9 minutes, 33 seconds Selection: reoptimation R1.00-00 Next we R3 and R5 activate the forwarding adjacency, then R3 and R5 will be advertised in this region of the Tunnel- ( L in the manner of direct links). 0x4F65 Mpls traffic-eng tunnels mpls ip It is strongly recommended to enable this command to view some logs of the isis adjacency . The default is closed. Periodic reoptimize ! Tag Reservable Bandwidth[2]: *Aug 18 04:37:06.239: peak rate =250000 bytes/sec The configuration of R1 is as follows: Copy this value. Ip rsvp bandwidth 687 NHop ( Next Hop Router ): Next hop router, PLR next hop router OSPF ! Device Configuration LSP Holdtime *Aug 18 09:06:02.699: 10.1.45.4 (Strict IPv4 Prefix, 8 bytes, /32) Hello data unit: sent periodically to determine whether other ISs are running IS-IS , establish adjacencies, exchange LSPs , and synchronize LSDBs . *Aug 18 11:31:44.598: Local Prefix 302 10.1.34.0/24 75000 42000 IP interface address Tunnel mode mpls traffic-eng Configure this hidden command on the penultimate hop router (that is, R2 in the figure above ): Clear domain authentication Ordered control mode : Odered Control Activate the MPLS TE extension for each router's OSPF and manually set the RouterID for MPLS TE . Downstream cannot assign labels, no MPLS enabled 0 kbits/sec End LSP ID : End LSP ID . Indicates the last LSP ID of the LSP range described in the TLV field . MPLS TE of AutoRoute characteristics of the TE tunnel as a direct link participating SPF calculation (except R2 themselves) 10.1.12.2 Regular area (non-backbone area) 10.1.23.2 ! Let's look at an example: Route-map test permit 10 router isis i L2 1.1.1.0 [115/30] via 10.1.34.3, Serial0/1 Label_request Fa0/0 Set as a P2P sub-interface or broadcast link (if it is fully interconnected) 400 MPLS and Tag switching Types of The global configuration command metric-narrow can be restored to the original default configuration. Fa0/0 Domain-wide Prefix Distribution with Two-Level IS-IS Level1 : Relative to the concept of a single area, consists of L1 routers in this area, and its routing information is published to Backbone . Route summary divides the original segment of LSP into two segments Mpls traffic-eng tunnels mpls label range 100 199 Next-address 10.1.34.4 The configuration of R4 is as follows: Configuration change IP Address: Metric: 10 *Aug 18 09:06:07.919: 10.1.45.5 (Strict IPv4 Prefix, 8 bytes, /32) The previously mentioned IS-IS , which only supports the CLNS network environment, does not support routing information exchange in the IP network environment. Later, the IETF in RFC 1195 are of IS-IS with modifications and extensions, called integrated IS-IS ( the Integrated IS-IS ) or dual- IS-IS ( Dual IS-IS ). Integrated IS-IS was developed to enable it to be applied to both TCP/IP networks and OSI networks, enabling it to provide dynamic routing information exchange for IP networks.
Exam Code: 200-125
Certification Provider: Cisco
Certification Exam Name:CCNA Routing & Switching
Update Date: Oct 02,2025
Cisco Dumps Popular Search:
free ccna exam ccnp switch modules ccna certification exam questions and answers pdf cisco ccnp tshoot book certcollection.org ccnp tshoot 642-832 ccnp route 300-101 ahmed nazmy cisco ccie lab exam fee ccnp switch renew ccna ccna dumps june 2019
Copyright © 2025 PASSHOT All rights reserved.