ccna paper pattern

ccna paper pattern

55.55.55.55 [110/31] via 10.1.23.3, 00:02:29, Ethernet0/1 Mpls ldp neighbor 1.1.1.1 targeted ldp L1/L2 router re-releases external routes into IS-IS ( to level1 ) Tunnel priority In-label Out intf/label Requirements for IGP *Aug 18 09:06:02.699: Minimum Path Bandwidth (bytes/sec): 1250000 2.2.2.2/32 Network 10.1.45.5 0.0.0.0 area 0 Router , thus maintaining two independent L1 link state databases and L2 link state databases. Then, if there is a router in the backbone that is not connected to the L1 router ,ccna paper pattern, it can be configured as an L2 router . Ip address 3.3.3.3 255.255.255.255 Pop tag How does a router know whether a message is a normal message or a label packet? MPLS packets are inserted between the Layer 2 header and the Layer 3 packet. Restrictions: Does the MTU of both parties match? Ip cef OSPF C It is also to check the FIB table, find 301 corresponding to the tag outgoing label is PoP and the next hop is D , then the head will pop up labels, which expose the original IPv4 data, C will be to the packet D . 16 *Aug 18 04:37:06.239: General Parameters break bit=0 service length=8 Each of our IS generates an LSP , and the first segment of the LSP is numbered 0 . But if my LSP is particularly large, it exceeds the interface. ISO IS-IS Routing Protocol *Aug 18 09:06:07.919: SENDER_TEMPLATE type 7 length 12: Type 1 length 12: At this point for R2 , he has two paths to 5.5.5.5 and 55.55.55.55 . Modify target ldp session related parameters Router ospf 1 Type-10 Opaque Link Area Link States (Area 0) 55000 The loopback0 address space of all devices is xxxx/32 , and x is the device number. 10.1.23.0 [115/20] via 10.1.34.3, Serial0/0 In a Frame Relay network, SNPA is DLCI Network 1.1.1.1 0.0.0.0 area 0 Path option 10, type dynamic (Basis for Setup, path weight 3) The configuration of R2 is as follows: IS-IS area Tunnel mode mpls traffic-eng tunnel destination 4.4.4.4 BGP routing problem, well, now we use the loopback interface on R1 and R4 to establish IBGP adjacency, the problem is solved. At this time R4 , the go 5.5.5.5 next hop of the R1 of Loopback port addresses, R4 at destined to 5.5.5.5 of the IP when the pressure package label, use is 1.1.1.1/32 routing tag, The same is true for R3 and R2 , then the label package can be opened through 1.1.1.1/32 . *Aug 18 09:06:07.919: Setup Prio: 7, Holding Prio: 7 ! Next, R3 receives the tag package. Similarly, look at your own LFIB : ATT/P/OL *Aug 18 11:26:02.546: RRO Network 2.2.2.2 0.0.0.0 area 0 The mere motivation to set up overload due to insufficient device resources is now running out. After all, the performance of the device is getting better and better. Router alarm tag The loopback0 address space of all devices is xxxx/32 , and x is the device number. Ip cef Ciphertext LSPs authentication The configuration of R2 is supplemented as follows: Globally activate MPLS TE tunnel and set MPLS label space 9 722 LDP session establishment 17 [Supplement] The non-pseudo-node LSP represents a router , including all ISs and LANs connected to this router . L1/L2 router BandwidthOverride: disabled LockDown: disabled Verbatim: disabled For the setting of SystemID , it is customary to encode the interface MAC or IP address of the router into a system ID or a part of it. Loopback IP is commonly used for this purpose in integrated IS-IS . For example, I have configured a loopback : 192.168.1.24/32 , and then I will complete this IP , not enough 3 digits to add 0 in front , forming 192.168. 001.