ccna voice lab

ccna voice lab

C 1.1.1.0 is directly connected, Loopback0 5.0.0.0/24 is subnetted, 1 subnets This bandwidth is reserved for the TE tunnel . If the bandwidth value is not added after the command, the default is 75% of the interface bandwidth. Intermediate System Intermediate System Mlps ldp neigbor [vrf vpn-name] ip-addr password [0-7] pswd Regional separation Fa1/0 Section LAN ID as 1921.6811.1001. 03 . " the routers connected to the multiaccess network (Ethernet) all have the same circuit ID . The circuit ID is a one-octet number that the router uses to uniquely identify the 75000 Router ospf 1 IP 1.1.1.0 255.255.255.0 IS R3.02 R1#sh mpls traffic-eng topology 1.1.1.1 (1.1.1.1 is a local router ) ! 10.1.35.5 -> 1.1.1.1 : FastEthernet1/0 (next hop 10.1.34.4) Ciphertext interface authentication 10.1.12.2 1.0.0.0/24 is subnetted, 1 subnets Interface fast0/0 The flooding and interaction of LSPs eventually form the IS-IS link state database. Tag information from 10.1.15.0/24, shared local tag: 403 Interface loopback1 Src 1.1.1.1, Dst 5.5.5.5, Tun_Id 0, Tun_Instance 31 RSVP Path Info: In the standard SPF algorithm, there can be multiple equivalent paths to the same destination. We call it ECMP ( Equal-cost Multipath ). Link IP Address: 10.1.23.2 *Aug 18 09:06:07.919: version=0, length in words=7 RFC1195 Data link layer address Mpls traffic-eng router-id loopback0 mpls traffic-eng area 0 Note that since R1 activates MPLS LDP-IGP synchronization, before the LDP adjacency relationship between R1 and R4 is established, the interface connecting R4 on R1 will not send OSPF HELLO packets, that is, R1-R4 . OSPF adjacencies can never be established. Of course, we don't want to watch the R1-R4 screw up,ccna voice lab, it's not good for anyone, isn't it? So configure one on R1 : Partition repair: on . 8 bits if the LSP originating router supports the repair area division is set this field Attached bits : the first 4-7 bits, for setting the LSP association with another area available with the following metrics: of . 4 -bit - default; 5th bit - delay; 6th bit - overhead; 7th bit - error Interface loopback0 Ciphertext interface authentication 202 Ip route 55.55.55.55 255.255.255.255 tunnel0 R2.00-00 ! IS-IS Level-1 Link State Database: Certification Information MPLS TE considers the attribute parameters of the link (such as delay, jitter, etc.) But if we modify the configuration on R1 : Reservable Bandwidth[3]: Set-overload-bit Tib entry: 3.3.3.3/32, rev 13 ISIS for NBMA support network is still flawed, as in the previous experiment demonstrates, if it is run on a Frame Relay main interfaces ISIS , or P2MP run on sub-interfaces ISIS , then you must ask PVC full-mesh, otherwise, the route study Not normal, but even if the PVC is fully interconnected, there are hidden dangers. If a PVC fails, routing will still have problems. Ip address 10.1.24.4 255.255.255.0 Mpls traffic-eng router-id loopback0 mpls traffic-eng area 0 The configuration of R5 is as follows: Test . 5 : SET 'bit-overload-the suppress interlevel 1096 Mpls ip Area-password P2P Links: Multiacces Links: The LSR route may receive multiple labels of a specific prefix ( distributed by multiple LDP neighbors), but he only needs to use one of them. The IP routing table is used to determine the next hop of the IPv4 prefix ( the construction of the LFIB needs one). IGP routing table, because the next hop of LFIB is calculated from the IGP table). The LSR uses this information to create its LFIB . The label bundled locally in the LFIB is used as an inbound label, and the label advertised by the LDP neighbor is used as an outbound label.