ccna 200-125 dumps 2019 pdf

ccna 200-125 dumps 2019 pdf

Neighbor 2001::1 next-hop-self Interface Serial0/0 R3 associates the route-map with the redistribution of the direct route 3.3.3.3/32 , tag#11 , and the route is passed to R2 . On R2 , the redistribution of RIP to OSPF is deployed. After the external route of 3.3.3.3 is injected into OSPF , the tag value is carried by default. GRE tunnel basic experiment Interface Loopback0 No synchronization exit-address-family ! Interface Loopback0 FE80::CE00:10FF:FE58:0 DAD Access-list 1 permit 100.1.1.0 RIP version number: The configuration of R1 is as follows: The node has two protocol stacks, IPv4 and IPv6. netsh interface ipv6 add route 3333 :: / 64 21 nexthop = fe80 :: 1 !! add an object of 3333 :: / 64 of IPv6 routing number associated with the index 21 interface, the next hop is fe80 :: 1 NA 136 The A record in IPv4 is used to map the host name to a V4 address, and the AAAA resource record maps the host name to an IPv6 address. We can do a test: Ipv6 nat v6v4 source 2001:1::1 202.101.100.111 Ipv6 unicast-routing interface fastEthernet 0/0 R1 and R3 respectively apply for the public network Ipv4 address and configure a dynamic 6to4 tunnel. In R1 ,ccna 200-125 dumps 2019 pdf, for example, arranged Tunnel 0 , assign an IPv6 address ( 6to4 address), this address is R1 is V4 external network address corresponding to the IPv6 6to4 address, i.e. 202.101.12.1 corresponding to The command distribute-list out works only on the routes being redistributed by the Autonomous System Boundary Routers (ASBRs) into OSPF. It can be applied to external type 2 and external type 1 routes, but not to intra-area and interarea routes. Redistribute ospf 3 subnets route-map OSPF3to2 After 10.30.0 is passed to R3 , since the RIP updated subnet and the R3 interface subnet belong to the same main class network, R3 receives the update, and uses the interface mask as the mask of the RIP route, so the R3 routing table The route loaded in is: 10.1.20.0/24 Y The range of TAG values ​​in the external LSA Fa0/0 134 8 bits Basic router configuration The MPBGP neighbor relationship is activated between PE1 and PE2 to prepare for the delivery of IPv6 routes. Segment header Fragment Header (Protocol 44 ) Interface FastEthernet0/0 Image 2023::3 Route-map test permit 10 match ip address 1 Image Then PC ping 10.1.13.0 , the data goes R1 ; IPX -> moving to Unassigned F : Reserved. Adjust the parameters of the NDP message Image 0000 010x xxxx xxxx IGRP Prefix announcement overview Image CISCO IPv6 Network Implementation Technology: CISCO self-study : Implementing Cisco IPv6 Networks (IPv6)Ip local policy route-map x Prefix announcement overview Used to increase the route metrics learned through EIGRP or RIP when inbound or outbound . Verify set ip default next-hop 11 In direction Ipv6 address 2001:1111::/64 eui-64 no ipv6 nd suppress-ra On R2 , in order to reach the network connected by R1 , R2 configures a tool that uses route summarization, referring to a summary route: 192.168.0.0/16 to R1 , although this does serve the purpose of network optimization, but this summary route Too "rough", it even includes the network segment on the R3 side, we call this behavior not accurate enough. Therefore, an ideal way is to use a "just right" summary route that includes these detailed routes, so that you can avoid the problem of insufficient aggregation.