ccna screen dumps

ccna screen dumps

Image Situation 1 Distribute-list 1 in 1/1024 100 Image Route-map test permit 10 R1 , R2 , and R3 run RIP and only announce the direct link between the three. In R1 the ip default-network 172.16.0.0 Ipv6 route ::/0 tunnel 0 !! When the route matching ACL1 when Mpls ldp router-id Loopback0 mpls label range 400 499 Source starts to send IPv6 packets using MTU=1300 , and the packets reach the destination smoothly. Fa1/0 Image Required IPv6 address Access-list 1 permit 172.16.10.0 Access-list 1 permit 192.168.12.0 router rip CISCO IOS does not yet support tunnel servers. Authentication Type Configuring Example 6 Deploying Distribution Lists When Republishing Between Protocols Fast tag rewrite with Fa1/0, 10.1.23.3, tags imposed: {301 403} Flags if not managed bit = 1 indicates that the host is automatically configured with stateful address (eg DHCPv6 ); not This path. And because there is no RIP route in the routing table , the natural RIP re-release to OSPF fails, and even worse, R4 about 0 00:00:39 The forwarding entry is only (and the outgoing interface list is empty) and will not be processed further. These multicast data are then discarded at R2 . Interface fastEthernet 0/0 ipv6 ospf 1 area 0 ! TCP Ip route 10.1.1.0 255.255.255.0 10.1.254.1 Domain name system After the PC , the PC regards the Router as a gateway, this lifetime Address Such as: 2001 : 00 a8 : 0 207 : 0000 : 0000 : 0000 : 0000 : 8207 Neighbor 2001::1 activate R4#sh isis database Interface serial0/0 Router(config-router)# distance ospf external ad1 inter-area ad2 intra-area ad3 ! 100.1.1.0/24 . At the same time,ccna screen dumps, this re-release becomes the summary route of OSPF . Even if two ASBRs are returned , because there is a static summary route locally, the summary route of OSPF is directly ignored , and sub-optimal is not generated. Path, this route will not be re-released back to RIP and cause other problems. The basic IPv4 header contains 12 fields, 20 bytes long. The options and padding fields are added as needed. Under normal circumstances, Rl is possible to ping through 3.3.3.3 , but if R2 f0 / 0 port agent arp turned off, then it ping nowhere outlet associated with the use of static routing, the router will route to the destination address that is the local chain Road, so send arp request for mac of 3.3.3.3 , and OSPFpassive-interface neither sends nor receives routing updates, nor does it send HELLO packets. Note that the IPv4 prefix 192.88.99.0/24 here should be published to the routing protocol on the IPv4 Internet. Otherwise this 6to4 relay using the anycast prefix is unreachable in the IPv4 Internet. 8 bits Management distance problem Net 49.0001.0000.0000.0002.00 If you want to turn off ICMP redirects, you need to use no ip redirects on the interface . Local site Bgp connected eigrp Authentication Header the Authentication Header (Protocol 51 ) Let's first look at the router: Ipv6 nd prefix 2012::/64 890000 720000 no-autoconfig Implementation of two-point bidirectional routing re-release Generate a default route Tunnel source serial 0/0 tunnel destination 10.1.23.3 0/0/0 Interface vlan 20 Mechanism involved Tunnel mode ipv6ip 6to4 interface fast1/0 This is the problem, how to solve it? Very simple, on the OR2 , deploy PBR , as long as the server data from Netcom, all forced to OR1 , it is solved. Mechanism overview Network 10.1.34.3 0.0.0.0 area 0 ! Image Experiment 1 For example, in the above figure, the network has two exit lines, which are connected to ISP1 and ISP2 respectively . If you want to let the intranet student users access the ISP1 line when accessing the external network , and the ISP2 line when the teacher network segment accesses the external network , This is not possible with traditional routing because traditional IP routing does not care about the source address of the data. This must be done with PBR .