cisco 200-125 dumps free download

cisco 200-125 dumps free download

Match metric matches the route with the specified metric. match route-type matches the specified type of route match community matches the BGP community. Network 10.1.34.4 0.0.0.0 area 0 Image Router-id 4.4.4.4 11 [Results] There is only 1.1.1.0 route in the routing table on R2 . The second command is to adjust the AD value for external routes, inter-area or intra-area routes . The red font part of the above output is the layer 2 MAC information and so on. The RA message of this response contains the /64 prefix of the IPv6 global unicast address configured on ISATAP . RIPng 6to4 automatic tunnel Redirect message relay. In this arbitrary play prefix, if the defined IPv4 address of the nearest 6to4 relay is 192.88.99.1 , then the address is ! EIGRP 850 10.1.12.2 Ipv6 nd prefix 2012::/64 at xxx yyyy 2.2.2.0 Routing Although the next hop is directed to R1 , it does not use the outbound interface to create routing entries. From the experimental phenomenon, it is not matched by the match . Needless to say, 3.3.3.0 , the associated interface is s0/1 . PMTUD R 3.0.0.0/8 is possibly down , routing via 9.9.12.2, FastEthernet0/0 Valid lifetime 2591944 preferred lifetime 604744 Joined group address(es): Case: Problems in the environment of education and telecommunications dual-export NAT network through PBR V1 defaults to send v1 to receive v1, v2 Exit-address-family Experimental needs Match ip address matches the access list or prefix list Ip sla monitor responder Y Image Image The buddy first introduced the above network environment. This Nima is a fairly classic case. OR1 and OR2 are the egress routers of the network, which are respectively connected to the egress lines of Netcom and telecommunications. PAT is implemented on both egress routers , so that intranet users can access the extranet. In addition to OR1 , Router isis Ipv6 address 2001:34::4/64 Image The configuration of R2 is added as follows: Ip address 10.1.12.1 255.255.255.0 Fa0/0 Router request ( RS ) 200-299 ; P has a label space of 300-399 ; PE2 has a 400-499 . Becomes 24 bits, appears in HELLO package, DBD package, and router LSA , network LSA , interAreaRouter LSA , Link LSA I can't ping because I found a subnet route after looking up the table at 172.16.1.1 . Therefore, the search is limited to the subnet route, and then the route is found to be mismatched. Therefore, the packet is discarded directly without going through the default route. . Ip address 192.168.20.254 255.255.255.0 Interface FastEthernet1/0 OR2 configuration The second command is to adjust the AD value for external routes, inter-area or intra-area routes . Image Exit-address-family Ipv6 address test ::FFFF/64 Image Authentication Type Weight Configuration example The tunnel is automatically enabled between isolated hosts on the IPv4 network to implement IPv6 data transmission in the tunnel. Source and destination IPv6 addresses are lower 32 The link layer supported by IPv6 requires a minimum MTU of 1280 bytes. The following are the parameters used during and after the auto-configuration process: Route-target export 234:4 RIP also supports tags ,cisco 200-125 dumps free download, but it must be version 2 . If multiple candidate default routes are specified using ip default-network , then the lowest AD will become the default route and set as the default gateway ( gate of last resort ). If AD is equal, then show ip route The first one is displayed as the default gateway. If both ip defaut-network and ip route 0.0.0.0 0.0.0.