ccnp tshoot exam code

ccnp tshoot exam code

Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale 2011-12 100 Metric Neighbor 10.1.13.1 remote-as 100 *>i100.0.2.0/24 Async Async interface Ip prefix-list ABC seq 5 permit 0.0.0.0/0 le 32 Ip prefix-list 1 permit 100.0.1.0/24 ip prefix-list 2 permit 100.0.2.0/24 route-map LP permit 10 * i The CISCO IOS version prior to 12.0(22)S and 12.2(15)T does not support this feature, and older IOS versions of the router restart exist. The AD value of 11.11.11.0/24 is adjusted to be larger than OSPF , for example 130 . So the configuration is as follows: CISCO default MED is 0 , optional non-delivery The PC has obtained the address and viewed dhcp snooping bingding databsae on SW1 : Router bgp 100 10.2.12.1 from 10.2.12.1 (1.1.1.1) The type parameter in the above command is used to indicate the hardware type of this hardware address. If type is 1 , the type is ethernet , if type Locally find a route to the neighbor and try TCP three-way handshake. Waiting for completion, the authentication is completed during TCP setup. If the TCP connection is not up, enter the Active state and try to connect repeatedly. Router ospf 1 ACLs to release or discard ARP packets. Ip address 192.168.100.254 255.255.255.0 The interface will not send BPDUs , and will also ignore received BPDUs. / / Modify the default parameters On R1 , only the summary route 32.0/21 is filtered, and all the detailed routes are released. If a standard ACL is used to match the route, how to write it? Router(config-dhcp)#network [network address][subnet mask] In addition to matching 100 to 106 outside the AS_PATH Synthesis example 1 : Forwarder 1 State is Active Ip address 5.5.5.5 255.255.255.0 Matching 1256 and 123 456 Mtu 1500 , so it will be fragmented, then on R2 , the two fragments are reorganized. ---------- The route works, but it is basically not used now, because the uncertainty is too strong) If the interface is trunk , set the trunk protocol type After receiving the BPDU packet, the interface will immediately switch to the err-disable state. Re-routing interface connecting the local release, static routing weight is 32768 Redistribute ospf 1 match internal external 1 external 2 Mode Ip prefix-list 1 permit 172.16.1.0/24 ip prefix-list 1 permit 172.16.2.0/24 route-map test permit 10 ARP packets are detected and released directly. For untrusted interfaces, ARP packet after receiving back checks only legitimate ARP packets can not be released, if the emergence of illegal ARP packets, it will be log , while discarding. Redistribute ospf 1 route-map test RFC1058 Router(config)#router rip After completion of the above-described basic configuration, we can at R5 to see the phenomenon, R5 simultaneously from R2 received 100.0 route segment, also from R3 received from the R1 release of 100 route segment, the final R5 will The route of R2 is preferred , which is matching this rule. Neighbor 4.4.4.4 update-source Loopback0 3.0 this route. This is an example of the use of a distribution list. Of course, it has a wider range of applications. The configuration of SW2 is as follows: //Get out a summary route instead of the default route Double-point bidirectional routing re-release 91 1,20,30 Ip address 192.168.20.254 255.255.255.0 Neighbor R3 filter-list 1 weight 4000 Situation 3 Origin IGP, metric 0, localpref 100, valid, external, multipath, best Router(config-router)# distance eigrp internal-distance external-distance Offset-list { access–list-number | name } {in|out} offset [ interface-type interface-number ] Device ID None | permit }} Redistribute ospf 1 match external 1 external 2 The IEEE802.3 frame can be divided into the following categories according to the values ​​of the DSAP and SSAP fields: ? This is because ip default-network is classful , so if you use this command to mark a subnet of a main class network, the router will actually install the main class network route corresponding to the subnet into the routing table without any deficiency. Provincial routing. So at this time, on the basis of the above,ccnp tshoot exam code, since the route of 172.16.0.0 is generated , the ip default-network command can be used again.