ccnp tshoot lab manual version 7

ccnp tshoot lab manual version 7

If BGP routes are passed from EBGP peers Update message: contains the entire routing table, updated periodically 0 100 0 100 i Path Configuration view and verification 3.5 RSTP (802.1W) Matching 1256 and 123 456 Match comprising 100 and 200 of AS_PATH Although the network devices are in the same subnet, they belong to different pVlans , and communication between pVlans must be implemented through the default gateway. Router ospf 1 Track 1 rtr 1 reachability No default (Of course, in the case of FA=0.0.0.0 ), then, in this figure, if the cost of R2 to ASBR-R3 is smaller, the final R2 will be preferred. If it is unreachable, the suppression timer is started at the same time. If the timer expires, the same neighbor still advertises the When a data frame is sent from the Hybrid port, the switch determines whether the attribute of the VLAN on the port is Untag or Tag . If it is Untag , first strip the VLAN tag of the frame and then send it ; if it is a Tag , send the frame directly. Origin IGP, metric 0, localpref 100, valid, internal, best Originator: 1.1.1.1, Cluster list: 2.2.2.2 R2#sh ip b 100.100.100.0 Milne 's packet was sent to Roo because he learned the wrong one. Apply the configured ARP ACL to the DAI. Once the portfast port is connected to the device, the interface can bypass the listening and learning states and enter the forwarding state directly . The route closest to BGP NEXT_HOP is preferred , and the route is the route with the smallest IGP metric to the next hop router . C 192.168.12.0/24 is directly connected, Serial0/0 1.0.0.0/24 is subnetted, 1 subnets Unicast Update Port The BGP configuration of R4 is as follows: 10.1.23.2 from 10.1.23.2 (10.1.23.2) Must be a zero field. Routing Protocols Via 10.1.13.3, FastEthernet1/0, 0 dependencies Aggregate-address 172.16.0.0 255.255.0.0 as-set summary-only The idea is the same as Experiment 2 . In this way, SW2 will accept these DHCP messages and process them, and the PC will be able to obtain the address. Vlans in spanning tree forwarding state and not pruned Note that the above two configurations are invalid for manually configuring the secure address of switchport port-security mac-address 00b0.9999.9999 . That is, the static security address entry configured by the above method never times out. No-export Route-map can be used in different commands for specific purposes Ip rip trigger Router (config) #server dhcp turn on DHCP services. By default, the Cisco IOS DHCP server and relay agent features are enabled on your router [Experiment 7 ] There are subnet routes (no match); there are default routes 10.1.13.1 Route-map cisco permit 20 match ip address 2 set metric 20 (for forwarding delay),ccnp tshoot lab manual version 7, this TC will last for 35s ( 20+15 ) At the same time network 1.0.0.0 , then 1.0.0.0 will be announced When 10.4.0.0 is hanged , C will immediately send a route poisoning message ( 10.4.0.0 16 hops) and then advertise it; 100 i Because RIP appeared earlier, early routers used serial link interconnection (point-to-point links), so RIP triggered updates only supported on point-to-point links, for Frame-Relay and Ethernet. In the multi-access interface, RIP trigger update is not supported , but the Frame-Relay point -to- point sub-interface is considered by RIP to be a point-to-point link, and the trigger update can be enabled.