ccnp route exam fee in india

ccnp route exam fee in india

Revoked route OK 1 ? RIP-1 only sends RIPv1 updates Allows up on a single switch . 8 th 802.1q to ISL vlan mappings BGP Identifer ROUTER-ID and OSPF selected routerID consistent manner Match ip address 1 Routing Information Protocol Router(config-router)# passive-interface int- type int-num 2 : Clear text verification; The Fa0/0 interface is divided into two sub-interfaces, and the encapsulation protocol Dot1Q is configured . At the same time, the traffic is tagged with VLANs , so that a trunk is started between the switch and the router . The two sub-router interfaces are arranged two VLAN gateways in the IP , as VLAN user gateway. Destination Address (Route Prefix): This is the destination network number associated with the route entry. A complete route prefix consists of: network number + prefix length ! Set ip next-hop recursive If an error occurs after receiving the open message, a Notification message is sent . If not Path Neighbor 1.1.23.2 route-map test out Experimental example: Called when republishing The red font part of the above output is the layer 2 MAC information and so on. 10.1.13.1 0 , regarded as infinity Again rule 11 , it seems to take effect, but this time the R3 of BGP routerID than reform R4 large, found R5 Still preferably R4 , because "If a path contains RR properties, producer ID to select the optimal path during Instead of RID ” None Last update from 192.168.101.10 on Serial0/0, 00:12:46 ago Routing Descriptor Blocks: : 000a.8a07.8280 Vlan 101 length Ip address 192.168.10.254 255.255.255.0 The main routing table version is injected into the last table version in the main routing table. R2#sh cef interface s0/0 policy-statistics input Serial0/0 is up (if_number 4) For non-equivalent load balancing, see section 5.3. R2(config)# access-list 1 deny 192.168.3.0 R2(config)# access-list 1 permit any R2(config)# router rip The static manually configured security address on the interface will not be converted to a sticky mac address. Detailed rules Features Overview Configuration Revision 15 The configuration of the DHCP server is a general configuration and will not be described here. ? Weight The type parameter in the above command is used to indicate the hardware type of this hardware address. If type is 1 , the type is ethernet , if type Basic experiment At this time, if another PC accesses the port, the port-security interface will receive a new data frame of the MAC address in the non-secure address entry , and the triggered violation action is given to the interface. Will be err-disable off. At the same time, a snmp trap message is generated . In addition, under the interface, the Security Violation Count will be incremented by 1. 0 packets, 0 bytes switched through the prefix tmstats: external 0 packets, 0 bytes The BGP router appends its AS number to the AS_PATH only when the update message is sent to another AS ( EBGP peer ) . This sentence also implies another meaning, that is, if you want to modify the AS_PATH attribute, you must execute the policy on the AS border router, and the policy of modifying the AS_PATH for the IBGP neighbor is invalid. Origin IGP,ccnp route exam fee in india, metric 0, localpref 100, valid, internal, best Y Some IOS does not support the neighbor R3 filter-list 1 weight command. CISCO private, the scope of this router is (not passed), this value will not be included in the update message, nor will it be passed to any R1 Experiment 2: weighted We can use the ip route-cache command , is enabled on the interface fast switching show ip cache to check the fast switching -related information . Port-Security deployment considerations Ip sla monitor 2 On R2 , going to the 100 network will use R1 and R3 as the next hop for equal load balancing (although R3 's uplink port has smaller bandwidth, but it is directly connected). 100 Route-map overview If an OSPF in- process route cannot be summarized: The configuration of SW2 is as follows: Match ip address prefix-list 30 set community 300:30 10.1.12.1 from 10.1.12.1 (1.1.1.1) Match ip address prefix-list 2 router bgp 100 R11#sh ip ro 8.8.8.0 A VLAN is generally a logical subnet composed of devices configured as members of this VLAN . // This command is used to advertise the real AS number of the AS outside the federation . Vlans allowed and active in management domain Elect a root port on each non-root bridge Bgp bestpath med confed Supplementary explanation of the role of the as_set keyword: Obviously, R2 is preferred to 10.1.12.1 . This is because the first 12 rules cannot be decided. Therefore, the neighbor IP is compared . Therefore, 10.1.12.1 is preferred . Of course, if the 10.12.1 address of R1 is changed to 10.11.12.1 , And on the R2 to do the corresponding modification of the neighbor ip , then R2 to 1.1.1.0 will switch to 10.2.12.1 , because this IP is small 100 Ip address 10.1.25.2 255.255.255.0 Whenever a route is reflected by the reflector, the cluster -ID of the reflector (the cluster) is added to the route's Cluster-list attribute. ? Default-information originate Avoid routing loops with triggered updates Ip arp inspection log-buffer logs number_of_messages interval length_in_seconds When deploying the campus network, we often have the following special requirements for switches: 192.168.1.0 declares that it has entered RIP , and R3 and R4 can learn this route and load it into its own global routing table. Then if we are at Can be detected when a violation time occurs, and can be punished Neighbor 4.4.4.4 ebgp-multihop 4 Router ospf 1 Loc-RIB BGP router selects the route by using its local routing policy for routes in adj-RIBs-In Select interface mode according to specific protocol 10.1.25.2 For example , the configuration of R3 is as follows: LocPrf Therefore, when the route lookup mode of the router is classless or the classless route lookup mode, the default lookup action of the router is the longest match criterion. For example, in the above figure, when R3 receives a packet and goes to 172.16.1.1 , then in fact, 172.16.1.1 is "dropped" in the network of 172.16.1.0/24 and 172.16.0.0/16 , both seemingly Yes , but 172.16.1.0/24 obviously has a longer match, so the packet is eventually dropped to R1 . Similarly, if there is a data packet going to 172.16.2.1 ? Since the entry of 172.16.2.0/24 is the highest according to the longest match principle, the data is thrown to R2 .