ine ccnp route workbook download

ine ccnp route workbook download

Commands Ip prefix-list 1 permit 100.0.1.0/24 ip prefix-list 2 permit 100.0.2.0/24 route-map LP permit 10 Non-default (manually configured non-default) priority and cost unchanged 10.1.13.1 End of a string Use the sticky MAC address on the port-security interface By default,ine ccnp route workbook download, only O and O IA routes in OSPF are redistributed into BGP. The Response packet contains a maximum of 25 routing entries. 0-65535 ( 0x00000000-0x0000FFFF ) and 4294901760-429496729502710046 Since the AS_PATH attribute does not change within the AS (only when the route leaves the AS ), the AS inner loop has a horizontal splitting mechanism, and the route reflector actually relaxes the horizontal splitting principle. This will bring some hidden dangers to the loop. Therefore, the route reflector needs to use the following two attributes to prevent loops: 5.5.5.5 Redistributing Routing Protocols 40 Route-map test permit 20 match ip address 2 ...... 192.168.8.0/24 When the network is normal, the data is forced to go ISP1 , ping 100 remote network data to ISP1 TCP connection establishment was successful, starts sending Open package, Open packet carries establish parameter negotiation peer. The next outgoing interface of the route is the port of the match . 5.5.5.5 SW2 puts the server into the same VLAN as the PC , which is equivalent to pure pass-through. Name server [Experiment 7 ] There are subnet routes (no match); there are default routes Neighbor 10.1.25.5 remote-as 345 Gratuitous ARP Vlan 100 For link state routing protocols such as OSPF Response message and check Private-vlan community Vlan 102 If both neighbor 1.1.1.1 weight and neighbor 1.1.1.1 filter-list 1 weight xxx are used , the latter is preferred The GW configuration is as follows: Advanced Features Next Hop Route matching tool 70 Neighbor 10.1.12.1 remote-as 100 O 2.2.2.2 [110/65] via 10.1.12.2, 00:05:16, Serial0/0 CAM table Neighbor 10.1.13.1 remote-as 100 100 i R1 and R3 , R2, and R5 establish an EBGP neighbor relationship. Solution: Modify the routing protocol management distance 98 200 i Let's review the 13 routing rules of BGP . In this lab manual, we will verify the main entries in the routing rules and familiarize ourselves with the various properties of BGP . BGP policy AS number . 2B , but with the network development, . 2B is not enough, so now expanded to 4 Ge B router bgp? You can view (Note: only available in certain IOS supported under version) The switch configured with Uplinkfast needs to be a stub switch or an access layer switch in the network three-layer structure. It cannot be the root bridge. The other side has received the Keepalive packet, the two sides agreed capability characteristics, started Update on LocPrf The cost value is increased, so that the OSPF metric of R4 going to 3.3.3.3 route becomes larger. What happens? Offset-list { access–list-number | name } {in|out} offset [ interface-type interface-number ] When the look-up table, the binary 0 , . 1 bits match, and for an exact match, i.e. purpose MAC and CAM table MAC needs Static route 20 If the local end has this feature enabled, the next-hop device does not support CDP , then switch to the next next-hop . If there is no next-hop , skip the PBR. Note that although R4 passes the route 400 {100 , 200} , the AS in the braces is only calculated as an AS in the AS_PATH calculation. Therefore , the two EBGP routes received on R6 have the same AS_PATH length. Finally, R6 The route of the oldest EBGP neighbor will be preferred . s> 172.16.10.0/24 In this mode, a data flow (Flow) in the first packet (Packet) will be placed into the cache system (system buffer). The destination address to the routing table will get a match query , the processing of the router device (CPU or Processer) while for CRC check , check whether the packet correctly . then Layer packet MAC address will be rewritten , replaced by the next-hop interface MAC address, this process will continue , for this data flow (flow) in the first 2 th, . 3 packets ...... same operation , comprising a routing table is rewritten MAC address , CRC checking. This method is undoubtedly the most delayed , because it uses the system buffer and processor to process each received packet .But we still have the opportunity to use this type of exchange , such as when performing load balancing based on each package , or when debugging ip packets .