ccnp route ios version

ccnp route ios version

UDP Ip route 172.16.1.32 255.255.255.224 192.168.23.3 Internal 0 packets, 0 bytes Ip route 172.16.3.0 255.255.255.0 172.16.12.3 Configuration Example 4 (at a single routing protocols -OSPF ) *>i100.0.1.0/24 Next hop Strictly speaking, path control is a very big topic. In the deployment of a large network, it is often necessary to consider the control of the data traffic access path in order to make more rational and scientific use and allocation of network resources. At the same time, it enhances the reliability, redundancy and robustness of the network. Received WAS, IT A SENDS that the LAN containing the BPDU DATE The up-to-Port Information Stored for that. the In the this Way, the inferior IS Discarded Information, and Superior Information The IS ON propagated Network. " Router bgp 200 None In a route-map statement, if there is no match statement, match all RIPV1 operational behavior 32 The number of messages sent by MsgSent to the neighbor Neighbor RC-ip remote-as 100 DHCP 0.0.0.255 will not work. Set the security address aging time to 50 min . Valid for secure addresses consisting of dynamically learned MACs learner Switch(config)# spanning-tree vlan-id Switch(config-if)# spanning-tree portfast [trunk] As shown above, the position of the line is 16+4=20 , so we get the summary address: 192.168.0.0/20 , which is the most accurate summary address. Configuration example 1 : as-path access-list with filter-list Transition from the old routing protocol to the new routing protocol Experiment 3 RIPv2 35 Ip address 10.1.45.4 255.255.255.0 NEXT_HOP on NMBA network ? Holddown timer expired A non-reflector router can participate in IBGP full interconnection or as a reflector client. Add configuration on SW2 : (global configuration mode) ip dhcp relay information trust-all RIPv1 3.1 Overview 20 Command Path Match ip address prefix-list 1 route-map RP2 permit 10 Supplementary explanation of the role of the as_set keyword: Add the following configuration on R5 : Half-duplex and full-duplex are the concepts of the physical layer, and the different access modes for the duplex mode of the physical layer are the concept of the data link layer, thus forming an important feature of Ethernet: the data link layer and The physical layer is relevant. Limit of inhibition: 2000 Interface loopback1 BGP table version is 3, local router ID is 4.4.4.4 As mentioned above, a route is allowed to carry multiple community values ​​to form a community list. If you want to delete one or several community values, for example, – LoopGuard and RootGuard cannot be enabled at the same time Portfast 1 Once the portfast port is connected to the device, the interface can bypass the listening and learning states and enter the forwarding state directly . Whether the MAC correspondence is legal Static The IP configuration is as above. The R2 interface is configured with two IP addresses, and both have announced that the entire network runs RIP . NEXT_HOP to 10.1.123.2 , then if C is not on the router to the IP of PVC , will be a problem, so this should be taken into account. Slot Slot unit 0 VC -1 Limit the maximum number of prefixes accepted from the neighbor. If this number is exceeded, the router will close the BGP connection with the neighbor. Apply clear ip bgp V Major Points The WEIGHT attribute is a CISCO private attribute. The scope is this router (not passed),ccnp route ios version, the value is not included in the update 200 Both R1 and R2 inject 100.0.1.0 and 100.0.2.0 into BGP using network . The meaning of this command here is that only 1.1.1.0 is allowed to go out of the route redistributed from the RIP routing protocol (to OSPF , there is no direction, as long as the interface is running OSPF ) Enable DHCP snooping on SW1 without going to no ip dhcp snooping information option , which is to insert option82 . The configuration of other devices is the same as the previous experiment. It is found that the PC cannot obtain the address . The debug message will be found on the gateway device, that is , debug on SW2 : relay information option exists, but giaddr is zero . The giaddr field means the IP address of the first DHCP relay agent that the message passed .