ccnp switch final exam answers 2018

ccnp switch final exam answers 2018

Interface f0/2 R2(config)# access-list 1 deny 192.168.3.0 R2(config)# access-list 1 permit any R2(config)# router rip If the router accepts the parameters of the neighbor in the OPEN message, it will answer a keeplive message, and send the message for the period of 1/3 of the holdtime (but not less than 1S ). CISCO defaults to 60S . If the hold time is 0 after negotiation , the keepalive keep-alive message is not sent . Match ip add pre 1 0 , regarded as infinity R3 has two BGP neighbors, one is 10.1.13.1 , which is an EBP peer , and the other is 4.4.4.4 is an IBGP peer . Arp spoofing solution 100.100.100.0 [20/0] via 10.1.23.3, 00:02:57 Route summary R2 , R3 , aiming RIP create static routing domain summary route, point null0 , while only these static routes redistributed into OSPF , and indeed can play a sub-optimal paths to avoid the question, but: Bgp dampening ? A the LLC sublayer own data to be transmitted is encapsulated, wherein the DSAP byte is filled B return to the SAP , the SSAP bytes are filled to their open the SAP , and then sent to MAC sublayer. *Mar 4 07:02:23.473: DHCPD: inconsistent relay information. By the original impact of routing attributes In the BGP table, only one route is preferred, which should be R3 (because R3 's RouterID3.3.3.3 is less than R5 's 5.5.5.5 ) The RRs have physical connections and establish BGP peer relationships. In the case where one of the RRs fails, the client still has an alternate connection. VLAN Interface Rate limit of ARP packets R1 and R2 are private partners. Some special traffic may need to be protected. Therefore , the dedicated line between R1 and R2 is added. If you want to ensure the traffic between 1.1.1.0 and 2.2.2.0 is exchanged through the leased line (running) the RIP ) away, when the green DOWN , only to take the following multi-access network. Policy-list Between R1 and R2 , the original R3 and R4 are updated through a multi-access network, and BGP is run . OSPF redistributed directly connected interface default cost20 ; redistributed static route default cost20 ; using the default-metric can modify and redistribute static routes into other routing protocols OSPF default after the cost , but this command to redistribute directly connected interface. invalid. Route reflector RR Encapsulation Status No synchronization no auto-summary Ip address 192.168.100.254 255.255.255.0 SwitchA hangs As shown above, the R1 deployment, R1 use heavy publishing directly connected with the introduction of the three external routes, then out distribution lists direction only SW1(config-if)# glbp 1 10.1.1.254 Interface fast0/1 Reference 39 " The When A Receives A Configuration Switch that the contains the BPDU Superior Information (Lower Bridge ID, path cost Lower, and SO Forth), IT Information Stores The Port for that. The this the If the BPDU IS ON The Received the root of The Port Neighbor management The shorter the AS-Path, the higher the priority. The BGP routing information database RIB consists of three parts: Router ospf 1 Paths: (1 available, best #1, table Default-IP-Routing-Table) Flag: 0x820 Unicast update 53 MED inherited IGP of Metric Y Run the switchport port-security mac-address command to configure a static security address entry. 3.3.3.3 Configure a static default route locally, such as ip route 0.0.0.0 0.0.0.0 null0 100 Modify the AD value of EIGRP Next turn on DAI on SW1 : (global configuration mode) ip dhcp relay information trust-all All BGP neighbors TCPsession and BGP neighbor state are reset Select the route with the smallest neighbor IP address ( the address of the neighbor in the neighbor configuration of BGP , that is, the update source IP of the neighbor ) Optional delivery As we R3 on the RIP routes injected into OSPF marked the Tag 1111 , then the next 0 100 0 100 i On R2 , in order to reach the network connected by R1 , R2 configures a tool that uses route summarization,ccnp switch final exam answers 2018, referring to a summary route: 192.168.0.0/16 to R1 , although this does serve the purpose of network optimization, but this summary route Too "rough", it even includes the network segment on the R3 side, we call this behavior not accurate enough. Therefore, an ideal way is to use a "just right" summary route that includes these detailed routes, so that you can avoid the problem of insufficient aggregation.