ccnp 300-101 route pdf download

ccnp 300-101 route pdf download

To verify which outbound interface is used for a particular traffic in destination-based load balancing, use If RP2 matching route exists in the BGP table, RP2 is advertised ; if RP2 hangs, RP1 is advertised. ! Configuring static routes Metric =0 Deception process ARP Request ... Set ip next-hop recursive Different OSPF between two-point two-way process re-release, can also use a static summary route re-issued, respectively, in two ASBR create different static routes summary above, re-publish static summary routes in the corresponding processes. And the preferred order is: i > e > ? Paths: (1 available, best #1, table Default-IP-Routing-Table) Flag: 0x820 Distribute-list 1 in ? All clients in the route reflection cluster should establish IBGP connections with and only with all RRs in the cluster. neighbor to mean),ccnp 300-101 route pdf download, BGP The network command, only the local routing loaded into BGP one way process. Packets with destination addresses that do not exist at the beginning of 192.168 are discarded directly. Normal traffic on other subnets of the 192.168 intranet will be forwarded according to the longest matching principle. All BGP neighbors TCPsession and BGP neighbor state are reset R4 ? The above match statement is used to match the summary route. ! EtherChannel / / View the routing flip situation MED setting method : 100 Path Y Redirection enabled *> 1.1.1.1/32 10.1.23.2 65 0 12 i Fast forwarding Experiment 3 LLC. ( The Logical Link Control ) by the destination service access point DSAP ( Destination Service Access Point ), source service access point SSAP ( Source Service Access Point ) and Hash The packet is captured as follows ( R3 sends the BGP update package to R4 ): IGRP for OSI networks Metric for redistributed routes Mobile routes Spanning Tree Protocol Second , select a root port on the non-root bridges SW2 and SW3 , as shown in the figure, because these ports reach the minimum overhead of SW1. Neighbor 3.3.3.3 remote-as 345 Configuration view and verification Index Interface vlan 10 RFC2080 The above network is equivalent to network 1.0.0.0 ( network has a class declaration) DMZ-Link Bw can only configure single-hop EBGP neighbors on this router. * i Ip prefix-list 2 permit 100.0.2.0/24 route-map WT2 permit 10 Compatibility Routing Information Protocol (RIP) Failure case analysis The configuration of R2 is as follows: The smaller the MED, the higher the priority Router ospf 1 Origin attribute (priority order: IGP > EGP > Incomplete ) In the route-map in the set community R1(config-router)# neighbor 10.1.12.2 route-map rp out *>i10.1.12.0/24 Neighbor 10.1.12.1 remote-as 100 Once the bridge is aware of a topology change in the network, it will send a configuration BPDU with the TC set , and each switch in the network will pass these set BPDUs , which will make each individual bridge aware. To the case of topology changes. Ip sla monitor schedule 1 life forever start-time now The TCP connection was not successfully established and the TCP connection was tried repeatedly . The BGP election routeriID rule is the same as OSPF . Then, first R2's own routing table will change, 3.0 routing is filtered out, and R3 is the downstream RIP router, 3.0 can not learn. Show ip bgp 10.10.10.0 on R3 Bridge ID to be unique bridge ID said earlier, is a priority and MAC constitute an address in the MAC address reduction scheme, all spanning trees of the same switch ID , the MAC address uses its own switch CPU 's MAC , At the same time , the priority of 16bits is expanded to become the system ID of 4bits priority + 12bits , and the system ID is used to identify different VLANs . In CISCO IOS , this system ID uses the VLAN.