ccnp tshoot 300-135 dumps 2019

ccnp tshoot 300-135 dumps 2019

Desirable: capita ask if the other side can/will 0 packets, 0 bytes switched through the prefix tmstats: external 0 packets, 0 bytes Neighbor 10.1.13.1 remote-as 100 30.30.30.0/24 Topology change mechanism (detection) IP CEF switching turbo vector Note that if you attempt this time SW2 on F0 / 2 interface priority piecemeal, and it is useless, because the port is looking at the sender ID . So if on SW1 , the port priority of F0/2 is reduced. Then on SW2 , F0/2 will win as the root port. Ip dhcp relay information trust-all Origin IGP, metric 0, localpref 100, valid, external, multipath , best distribute-list For example , the configuration of R3 is as follows: 300 {100,200}, (aggregated by 300 3.3.3.3) R4 on the show ip bgp 172.16.0.0 Ip sla monitor responder Secret level Floating Static Routes The election of the root bridge will not be said. Next, look at the two interfaces of RP and SW2, and both will receive the BPDU , and the BPDU received by the interface connected to the root will be received . Ip dhcp relay information trust-all As-path: all specific routes received as numbers are placed in {} , the calculation AS_Path the length of the AS is only counted as . 1 th AS 10 PVLAN port type GLBP We know that the data of the VLAN that the switch can support is very large. If PVST+ is enabled , each VLAN has a spanning tree, and no spanning tree must have a separate identifier. If you need to use a MAC , then the MAC address pool. It must be unbearable. Ip route 2.2.2.0 255.255.255.0 192.168.123.2 Ip nat inside source route-map nat1 interface serial0/0 overload ip nat inside source route-map nat2 interface serial0/1 overload ip nat inside source route-map nat3 interface serial0/1 overload None ! A macro command that specifies the interface mode as access and enables the portfast feature. 10.1.13.1 Network 100.0.1.0 mask 255.255.255.0 " The When A Receives A Configuration Switch that the contains the BPDU Superior Information (Lower Bridge ID, path cost Lower, and SO Forth), IT Information Stores The Port for that. The this the If the BPDU IS ON The Received the root of The Port The configuration of R2 is as follows: V1 defaults to send v1 to receive v1, v2 100 [Experiment 2 ] There are subnet routes (match); there are default routes, subnet routes Port Vlans allowed and active in management domain Fa0/20 1,10,20,30 Command 100 Router (config) #server dhcp turn on DHCP services. By default, the Cisco IOS DHCP server and relay agent features are enabled on your router Index Neighbor 10.1.12.2 advertise-map RP1 non-exist-map RP2 [Experiment 5 ] There are subnet routes, the subnet route prefix length is different (but both match),ccnp tshoot 300-135 dumps 2019, and the longest match 100 i SW1 (config-if) # glbp 1 priority 120 Network The Native VLAN must match at both ends of the trunk . Otherwise, VLAN traffic will appear. Local origin We can affect the routing by setting the LP value. For example, the same implementation allows R4 to access 100.0.1.0 and go to R3 , accessing 100.0.2.0. The BGP AS is planned as follows: R1 , R2 , and R3 each have a network loopback route in the BGP process (without any policy); route summarization is performed on R4 and R5 respectively: Ip local policy route-map x Router bgp 100 Deployment Highlights 63 -------------- 10.1.12.2 In the above configuration, the maximum number of secure addresses is set to 3 , and then a secure address is manually configured. Then there are two remaining , and the switch can construct a secure address through dynamic learning. Configuration last modified by 0.0.0.0 at 3-5-93 00:11:48 ! ? Send Update package If there are multiple routes from the same neighboring AS and multiple paths are available through Maximum-paths , all routes with the same cost are added to Loc-RIB. Detailed rules Vlan range Route-map test per 10 Set as-path tag Ip route 0.0.0.0 0.0.0.0 serial s0/2 Interface vlan 10 ? Gateway implementation) ip route 172.16.1.0 255.255.255.0 192.168.12.1 !! go subnet route Set metric 100 When port-security mac-address sticky is activated on the interface , then: 200 i 2.2.2.0, but the update is 2.0.0.0 after the summary Vlans allowed and active in management domain ISL RFC1058 About UDLD Known via "ospf 1", distance 110, metric 20 Switch(config)# vtp password x The Length field defines the number of bytes that the Data field contains. Rcp: Database agent URL 10.1.13.3 When BGP routes are redistributed to the IGP , the iBGP routes are not redistributed by default . Only EBGP routes are re-advertised . bgp redistribute-internal is required to make the iBGP routes re-released. Ethernet data link layer : ccnp 200 i Network 100.0.2.0 mask 255.255.255.0 neighbor 10.1.13.3 route-map test out Network 4.4.4.4 0.0.0.0 area 0 ip default-network Network End of a string 15 When both DSAP and SSAP take a specific value of 0xaa , the 802.3 frame becomes the ETHERNET_SNAP frame. Native vlan Using route reflector 23 BGP cannot automatically discover the neighbors as the IGP . The IP address of the neighbor is specified by the local BGP neighbor command. The source IP address of the BGP connection is the outgoing IP address of the traffic . Note that only the neighbors locally configured IP and neighbors for BGP source connection establishment IP is the same, BGP connection in order to be properly established, at the same time, to ensure that only one party can meet the conditions.