ccnp 300-101 vce dumps

ccnp 300-101 vce dumps

2/1 BGP path/bestpath attribute entries using 248 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 100 i Once the ORF is deployed , the BGP peers will negotiate the ORF capability in the open message when the BGP peer relationship is established . If the negotiation succeeds, the ORF content is pushed using the route-refresh packet . VLAN Interface Same speed and duplex FastEthernet1/0 UPDATE message Packets with destination addresses that do not exist at the beginning of 192.168 are discarded directly. Normal traffic on other subnets of the 192.168 intranet will be forwarded according to the longest matching principle. Or the above example, if we R1 on, of ping 1.1.1.2 REPEAT size. 1 1501 , at this time, R1 due to the generation of the IP packet is larger than Ip prefix-list 1 permit 1.1.1.0/24 route-map test 25 Tiao Spanning Tree Protocol When the RR sends a route update to an EBGP neighbor, it will be aware of the existing CLUSTER_LIST attribute. LocPrf AS64512 private AS number is not allowed to declare to the Internet , if unchecked, R3 received R1 route, the AS_PATH certainly contains 64512 This private AS number, assuming that R3 as Internet routers, how R2 on the R3 delivery route When shielding private ASs ? Just a very simple command: neighbor 10.1.23.3 remove-private-as Trunk overview Bibliography Exclude one or more addresses from the address pool (such as gateway IP, etc.) to avoid assignment to clients 2 : Reponse message, send all or part of its routing information, a Response Continue to look R4 result of the capture ( R3 distributed to R4 of BGP update package): Default route Preemption enabled, min delay 30 sec 4 ^$ On CISCO IOS , interface x interface mode: Communicates with other members of community and all promiscuous ports Ip address 192.168.10.254 255.255.255.0 i Core switch configuration: Neighbor 1.1.1.1 route-reflector-client Double-point bidirectional routing re-issuing problems 92 Command summary 81 R2(config)# access-list 1 deny 192.168.3.0 R2(config)# access-list 1 permit any R2(config)# router ospf 1 Neighbor 10.1.13.1 remote-as 100 ? Router ospf 3 Holddown timer expired AS number . 2B , but with the network development, . 2B is not enough, so now expanded to 4 Ge B router bgp? You can view (Note: only available in certain IOS supported under version) This is a feature that is used in large and medium-sized networks to make the configuration "modular". Neighbor 10.1.23.3 remote-as 300 neighbor 10.1.23.3 route-map test out Can only be passed between IBGP peers (unless a policy is made, the LP value will not be lost between IBGP neighbors within the AS ), not in EBGP Next Hop Trunking h routed ( dampening ) route, route may be faulty ( down ), with historical information, but no optimal route *> 172.16.0.0 Network Show ip cef Trunks can be statically configured or negotiated through DTP . Using ICMP protocol to detect 10.1.1.2 reachability (source address 10.1.1.1 to ping10.1.1.2 ) Track Object 's ID is 1 , associated to ip sla monitor 1 Not the routerID of R1 ,ccnp 300-101 vce dumps, because it is not necessary at all). 65 Match ip address prefix-list R2 Switch(config)# vlan dot1q tag native 100.100.100.0 [20/0] via 10.1.23.3, 00:02:57 IP policy routing is disabled Difficult to resolve The BGP configuration of R2 is as follows: Statically configure a dhcp snooping bingding dabase entry. The command is configured in privileged mode. Link aggregation mode R2(config)# access-list 1 deny 192.168.3.0 R2(config)# access-list 1 permit any R2(config)# router rip Backup port: Discard status. A backup of a specified port occurs when a switch has two ports connected to the same shared medium. Switch(config-if)# spanning-tree [ vlan vlan-id ] cost cost 8 Neighbor 5.5.5.5 ebgp-multihop 3 ? ? After receiving the Gratuitous ARP message, the peer knows that the user of the IP address already exists on the intranet, and then an alarm is generated. The MAC address in the ARP table is all zero ( Windows host) or " No completed" (network device) C 192.168.12.0/24 is directly connected, Serial0/0 1.0.0.0/24 is subnetted, 1 subnets Originator_ID Cluster_list Weight Of course, it is ok to filter the prefix list in the in direction on R2 . BGP table version is 1, local router ID is 4.4.4.4 Debug dhcp detail Set ip next-hop ip1 ip2 ip3 , this knowledge point is no problem, right? After the match is live, the packet is first sent to the first next-hop ip address . If the direct connection associated with the ip address is DOWN , then the next next-hop ip address is switched , so next-hop .