Free Cisco Written Dumps
For Top 50 Purchases 01:59:56

X

ccie lab 1000v

ccie lab 1000v


Here is the most accurate CISCO CCIE WRITTEN exam questions and answers. All study materials need to be carefully selected by professional certification experts to ensure that you spend the least amount of money, time, and pass the high quality exam. There is also a professional service team that can customize your study plan for you to answer all your questions, PASSHOT's CCIE Written Dumps is definitely the biggest boost for you to test CCIE that helping you pass any Cisco exam at one time.

Demo1:

ProblemServer 1 can not get ip address.

Materials:

SW3#show ip dhcp snooping  

Switch DHCP snooping is enabled

DHCP snooping is configured on following VLANs:

none

DHCP snooping is operational on following VLANs:

none

Smartlog is configured on following VLANs:

none

Smartlog is operational on following VLANs:

none

DHCP snooping is configured on the following L3 Interfaces:

Insertion of option 82 is enabled

   circuit-id default format: vlan-mod-port

   remote-id: 0018.b9da.5300 (MAC)

Option 82 on untrusted port is not allowed

Verification of hwaddr field is enabled

Verification of giaddr field is enabled

DHCP snooping trust/rate is configured on the following Interfaces:

 

 

Interface          Trusted     Allow option     Rate limit (pps)

 --------------------   -------         ------------     ----------------  

Q1Which material is most helpful

Q2:which packets can help you find the cause


Demo2:

Customer just setup a IPv6 Network, with HSRPv6 on R1 & R2. After setting up, all hosts lose connection.

What would you recommend to your L1 Engineer as a Quick Fix?

CE1 key configuration

standby 1 priority 200

standby 1 preempt

ipv6 nd router-preference low

CE2 key configuration

standby 1 preempt

ipv6 nd router-preference high 

 

 

I think it is a rouge device because I don't see any problems with the HSRPv6 config. PCs are configured with "ipv6 enable", "ipv6 autoconfig"

The R1 have a "ipv6 nd-preference high" and R2 have "low" if I'm not wrong.

 

How fast fix the problem?

 

¡ Shutdown the link between CE2 and PE2.

¡ Shutdown the link between CE1 and PE1.

¡ Configure CE1 with highest HSRPv6 Priority.

¡ Configure CE2 with highest HSRPv6 pirority.

¡ Configure CE2 with low HSRPv6 priority.

¡ Shutdown CE1 interface e0/0.

¡ Shutdown PE2 interface e0/0.

¡ Disable fast-switching on CE's LAN.

¡ Enable fast-switching on CE's LAN.

¡ Change HSRPv1 to HSRPv2 version


CCIE Routing and Switching LAB Dumps

( 17 People are currently looking at this product )

Exam Code: CFG: LAB1、LAB1+、LAB2、LAB2+、LAB3
TS: TS1(5 sets)、TS2(3 sets)
DIAG:DIAG 1~DIAG 8(8 sets)

Certification Provider: Cisco

Certification Exam Name:CCIE Routing and Switching Lab

Update Date: Oct 02,2025

Free Cisco Written Dumps
For Top 50 Purchases
Latest Dumps
Numbers of Question & Answers

    ccie lab 1000v

  • 1382 Reviews
  • 2. Support plug and play 1 1. Standard Access Control List 1-99, 1300-1999   equipment has been sent to the site, but no engineer has debugged it. I On the interface enabled with PPP   Configuring and Verifying a Policy for Management Traffic establishment and examination of the sp lab is a process from scratch. =========================================================== ===============   Ip host   4 silent timing controller 5. trigger updating   the course. I am ready to go back to rest at two o'clock. I Vlan database   Show ip route      3. NAT-PT communication between IPV6 and IPV4 network difficult person, a comrade in the sp lab named Li,ccie lab 1000v, the whole sp 1.Special line : PP P , H DLC, SLIP   FRAME-REL A Y topology (pvc)   Spanning tree port     UDP is a connectionless protocol. Faster than TCP, but unreliable, it pushes the responsibility of error control to the application.       The establishment of the control channel is similar to the Standard mode, but the Pasv command is sent after the connection is established. After receiving the Pasv command, the server opens a temporary port (port number greater than 1023 is less than 65535) and notifies the client of the request to transmit data on this port. The client connects to the FTP server and the FTP server will transmit data through this port.

Have any question for us?

Cisco Dumps Popular Search:

narbik ccie security v5 workbook ccna valid dumps 2019 what are ccna dumps ccna test prep questions spoto ccie sp dumps ccnp switch 9tut ccie r&s lab experience ccna routing and switching questions ccna wireless dumps free ccie security version change

Copyright © 2025 PASSHOT All rights reserved.