Exam Code: CFG: LAB1、LAB1+、LAB2、LAB2+、LAB3
TS: TS1(5 sets)、TS2(3 sets)
DIAG:DIAG 1~DIAG 8(8 sets)
Certification Provider: Cisco
Certification Exam Name:CCIE Routing and Switching Lab
Update Date: Apr 25,2024
RS Source IP :: Destination IP FFO2::2 There are two types of ACLs : Vlan division: 1, based on port; 2, based on MAC address; 3,ccie security written dumps 2018, based on IP address FRAME-REL A Y There are three working modes of the switch: 1. Store and forward - the data is stored in the buffer, and the CRC cyclic redundancy check is performed. If the packet has a CRC error, the packet is discarded. 2. The straight-through exchange is read-only. The first 6 bytes are searched for the destination address through the address mapping table and then transmitted to the corresponding port. 3. Fragment Discarding - A solution between the first two to check whether the length of the packet is 64 bytes. If it is small, if it is large, it will be forwarded.
Problem:Server 1 can not get ip address.
Materials:
SW3#show ip dhcp snooping
Switch DHCP snooping is enabled
DHCP snooping is configured on following VLANs:
none
DHCP snooping is operational on following VLANs:
none
Smartlog is configured on following VLANs:
none
Smartlog is operational on following VLANs:
none
DHCP snooping is configured on the following L3 Interfaces:
Insertion of option 82 is enabled
circuit-id default format: vlan-mod-port
remote-id: 0018.b9da.5300 (MAC)
Option 82 on untrusted port is not allowed
Verification of hwaddr field is enabled
Verification of giaddr field is enabled
DHCP snooping trust/rate is configured on the following Interfaces:
Interface Trusted Allow option Rate limit (pps)
-------------------- ------- ------------ ----------------
Q1:Which material is most helpful
Q2:which packets can help you find the cause
Customer just setup a IPv6 Network, with HSRPv6 on R1 & R2. After setting up, all hosts lose connection.
What would you recommend to your L1 Engineer as a Quick Fix?
CE1 key configuration
standby 1 priority 200
standby 1 preempt
ipv6 nd router-preference low
CE2 key configuration
standby 1 preempt
ipv6 nd router-preference high
I think it is a rouge device because I don't see any problems with the HSRPv6 config. PCs are configured with "ipv6 enable", "ipv6 autoconfig"
The R1 have a "ipv6 nd-preference high" and R2 have "low" if I'm not wrong.
How fast fix the problem?
¡ Shutdown the link between CE2 and PE2.
¡ Shutdown the link between CE1 and PE1.
¡ Configure CE1 with highest HSRPv6 Priority.
¡ Configure CE2 with highest HSRPv6 pirority.
¡ Configure CE2 with low HSRPv6 priority.
¡ Shutdown CE1 interface e0/0.
¡ Shutdown PE2 interface e0/0.
¡ Disable fast-switching on CE's LAN.
¡ Enable fast-switching on CE's LAN.
¡ Change HSRPv1 to HSRPv2 version
Here is the most accurate CISCO CCIE WRITTEN exam questions and answers. All study materials need to be carefully selected by professional certification experts to ensure that you spend the least amount of money, time, and pass the high quality exam. There is also a professional service team that can customize your study plan for you to answer all your questions, PASSHOT's CCIE Written Dumps is definitely the biggest boost for you to test CCIE that helping you pass any Cisco exam at one time.
Cisco Dumps Popular Search:
ccnp 300-115 lab questions ccna version 3 dumps ccnp route portable command guide ccna sample question paper how2pass ccnp route ccnp route dumps 2017 ccnp route 642-902 vs 300-101 ccnp switch podcast ccie rs v5.0 lab exam demo ccna 200-125 dumps
Copyright © 2024 PASSHOT All rights reserved.