Here is the most accurate CISCO CCIE WRITTEN exam questions and answers. All study materials need to be carefully selected by professional certification experts to ensure that you spend the least amount of money, time, and pass the high quality exam. There is also a professional service team that can customize your study plan for you to answer all your questions, PASSHOT's CCIE Written Dumps is definitely the biggest boost for you to test CCIE that helping you pass any Cisco exam at one time.
The following requirements were pre-configured
l VTP is turned off in all switches
l All required VLAN, including access-ports configuration in all relevant switches are provisioned.
l All required SVI interface in all relevant switches (including IP address and subnets mask) are provisioned.
Configure the network in all sites as per the following requirements:
l Access-port must immediately transition to the forwarding state upon link up, as long as they do not receive a BPDU. Use the minimal number of commands per switch to enable this feature.
l If an access-port receive a BPDU, it must automatically shutdown. Use the minimal commands per switch to enable this feature.
l Ports that were shutdown must attempt to automatically recover after 10 minutes.
l None of the switches may generate a TC.
configure the headquarters’ network as well as the large and medium office networks as per the following requirements:
l all trunks must use dot1q encapsulation
l negotiation of trunking protocol must be disabled in all switches
l distribution switches (SW300, SW301, SW400, SW401, SW500, SW501) must initiate etherchannel negotiation using LACP
l configure layer 2 etherechannel’s number as shown in the ‘diagram 1: main topology’ and ‘diagram 5: layer 2 connections’ (that is use only Po1 and/or Po2)
l ensure that all ports included in etherchannels are effectively in use and bundled in the expected channel
l access switches must see similar output as shown below:
configure the headquarters‘network as per the following requirements:
l SW300 must be the spanning-tree root bridge and must maintain a single spanning-tree instance for the following VLANs: 2000, 2002, 2004, 2006, 2008 (use instance number 2)
SW301 must be the spanning-tree root bridge and must maintain a single spanning-tree instance for the following VLANs: 2001, 2003, 2005, 2007, 2009 (use instance number 1)
l all other VLANs, except 3001, must share the default spanning-tree instance
l ensure that interface E0/2 of SW 300 and SW 301 is a dot1q trunk and that it switches frames for VLAN 3001 only
l SW300, SW301, and SW 310 must not have any blocked ports for any access VLAN (2000-2009)
l SW310 must have the least chance of being elected the root bridge for any VLAN
l none of the three switches may run more than four instance of spanning-tree at any point in time
configure all access switches in both datacenter networks (SW110, SW111, SW210, SW211) as per the following requirements:
l use 32-bit based values for the default port path cost
l all four switches must use the default value for their interface cost
configure the home router R70 as per following requirements:
l the Ethernet WAN link must rely on a layer 2 protocol that supports authentication and layer 3 protocol negotiation
l the service provider expects that R70 completes a three-way handshake by providing the expected response of a challenge requested
l R70 must use the hostname “R70”and password “CCIE” (without quotes)
l R70 must receive an IP address from R8 and must install a default route pointing to 201.99.8.8
l ensure that R70 can successfully ping 8.8.8.8, which is located in the ISP#2 cloud
l you are not allowed to configure any static route in R70 in order to achieve the previous requirements
l use the pre-configured Dialer 1 interface as appropriate
configure the headquarters network (BGP AS#65003) as per the following requirements:
l both gateway routers of the headquarters network must always advertise a default route into the ospf domain
l all four devices produce the exact same output as shown below. everything must match, except the “dead time” counters and line order
in order to speed up OSPF convergence in the datacenter#1 network, limit the number of IP prefixes that are carried in OSPF LSAs that OSPF is preconfigured in all required devices in datacenter#1
configure the datacenter#1 network as per the following requirements:
l all OSPF devices must exclude the IP prefixes of connected networks when advertising their type 1 router LSA, except for prefixes associated with loopbacks or passive interfaces
l host loopbacks are the only OSPF intra-area prefixes that may appear in any DC devices ‘routing table
l your solution must still apply if any new interface was added to the OSPF domain
l don not use any prefix-list or another explicit filter anywhere
l do not configure any interface as unnumbered
l do not remove any pre-configuration
R100 is located in the partner#1 network and is connected to R42. it supports OSPF only. configure the large office network as per the following requirements:
l R42 must run a separate OSPF process with R100
l as mentioned in item 2.6, the site gateways R40 and R41 area not allowed to redistribute OSPF into BGP and vice versa
l R42 is allowed to redistribute OSPF into BGP and vice versa
At the end of the exam:
l The server 2 (that is located in the Datacenter#2) must be able to ping the IP address 100.100.100.100/24 (that is located in the partner#1 network)
R100, the partner router, must receive the external prefixes as shown below and no other prefixes:
Exam Code: CFG: LAB1、LAB1+、LAB2、LAB2+、LAB3
TS: TS1(5 sets)、TS2(3 sets)
DIAG:DIAG 1~DIAG 8(8 sets)
Certification Provider: Cisco
Certification Exam Name:CCIE Routing and Switching Lab
Update Date: Sep 12,2025
=========================================================== =============== Which contains: BridgeID = Bridge Priority + MAC address Module 1: Cisco ASA Adaptive Security Appliance Essentials Connection Table and Local Host Table Serial1 is up, line protocol is up (It took half a month for troubleshooting 1 (1-BT7) and 5 days for TS2) Show version B(config)#inte s 0 B(config)#inte s 0 EBGP is also all good, router-id can be added up, MPLS is also fully pre-configured, when you improve the IGP, all the log prompts. R6(config-if)#ip address 1.1.1.1 255.255.255.0 6:30 AM Get up Frame-relay interface-dlci ??? Spanning-tree vlan 1 priority ? NAT on Cisco ASA Software Version 8.2 and Earlier the pressure of learning, there will be no strong desire for knowledge =========================================================== =============== Check to see CDP neighbor ( containing three layers of the IP address ) The running-config copy to tftp the service 1. refuse Worldwide unicast address: similar to the public address in IPV4, mainly used in the global Internet ICMP (Internet Control Message protocol) Upgrade the IOS command: B(config)#ip nat pool abc 1.1.1.1 1.1.1.30 prefix-length 24 Debug ip igrp transactions objectively speaking, without this certificate, they may not be able to ! OSPFv2 specifies that a port can only participate in one OSPF process. Configuring and Verifying Support for Dynamic Protocols Clockrate 64000 If the source sends data to the anycast address, the device that is closest to the source and configured with the anycast address receives data. It seems that Buff is a stuff, you believe it is still good, "the letter is there, if you don't believe it, there is nothing." I have already arrived in Beijing four days before the exam. Because there are things in the Beijing branch that require me to participate, I came over in advance. My first night,ccie lab switches, the second night of my super uncomfortable, no window plus Beijing's air conditioning, very uncomfortable! ! ! I personally valued the place, and finally changed a good place, with windows, sunshine, and quiet during the day. Every day after work, I will go to the Yintai Center and walk around. "I will come to customs clearance after two days, waiting for me! CCIE", because I followed a weekend and took a day off. So there are three days to prepare for the exam.
Cisco Dumps Popular Search:
how to study for ccnp switch testking cisco ccna dumps for ccna security 210-260 ccnp 300-101 dumps free ccna course material ccie security v5 lab setup ccna security dumps 2019 pdf ccie rs h3 ccnp switch 300-115 pdf 2017 591lab ccnp
Copyright © 2025 PASSHOT All rights reserved.