testking ccna torrent

testking ccna torrent

Attribute Flags: 0x00000000 Mpls traffic-eng tunnels ip rsvp bandwidth Administrator-weight , and only the IGP metric is used to calculate the shortest path of the tunnel . Is-type command such as is-type level-1 Type escape sequence to abort. Tracing the route to 5.5.5.5 Available bandwidth Ip address 10.1.45.5 255.255.255.0 3.3.3.3 Router-id 4.4.4.4 *Aug 18 09:06:07.919: SESSION type 7 length 16: [3]: 75000 kbits/sec Ip address 10.1.23.3 255.255.255.0 INIT 22 102 *Aug 18 09:06:07.919: label. Interface eth0/1 ! 0x10BA R3.00-00 Type 2 length 36: Fa0/0 Complete basic IP configuration (configuration omitted) Then, if you are in the tunnel port on R1 , use the following configuration: 0 kbits/sec Ok, now when R1 is going to ping 4.4.4.4 , R1 has to check its own FIB , which is the CEF table. Note that this is an IP lookup: Router(config-if)#tunnel mpls traffic-eng priority establish priority hold priority MPLS TE considers configuring (static) bandwidth on the link R3#show ip ospf database router 2.2.2.2 Ip cef !!tunnel establishment and retention priority IS-IS by Hello PDU padding size to the interface MTU large 75000 TOS 0 Metrics: 1 Device Internet segment 10.1.xy.0 / 24 , where xy is the device number, X small y large Mpls traffic-eng router-id loopback0 mpls traffic-eng area 0 ! Peer LDP Ident: 2.2.2.2:0; Local LDP Ident 1.1.1.1:0 R3.02 Basic experiment IS-IS link type Mpls traffic-eng tunnels ip rsvp bandwidth *Aug 18 04:37:06.239: Incoming PathError: !!R2 sends a patherror message to R1 This time, we do some tests, R1 configuration area-password and R2 are not the same configuration. In this way , although the neighbor relationship can be established for R1 and R2 , they cannot learn the route of the other party, because neither party recognizes the LSPs . Alternatively, you can configure the following command on the tail router: Configured in OSPF process mode, this command activates MPLS TE in a specific area. Although the implicit null tag also uses a tag with a tag value of 3 , tag 3 will never appear in the tag stack of the MPLS message, which is why it is called an implicit null tag. Route Distinguisher: 2345:6 Router(config-if)#tunnel mpls traffic-eng path-option x {dynamic | explicit {name path-name | Experimental procedure [Supplement] The non-pseudo-node LSP represents a router , including all ISs and LANs connected to this router . *Aug 18 09:06:07.919: version=0, length in words=7 RFC 3358 Network 10.1.23.2 0.0.0.0 area 0 We define the affinity attribute and mask of the TE tunnel of R1 . Then, when R1 calculates the path for this tunnel , R1 converts the affinity value 0x00000001 into binary,testking ccna torrent, which is configured with the two interfaces of R1 . The two attribute-flags values ​​are compared one by one. Since our mask configuration is 0x00000001 , it is also written as binary, and the mask is 1 bit, which must be matched, so only the R2-R2 link is available. . In the actual network deployment, we can flexibly define the meaning of each bit of the link attribute according to our own needs , and combine the affinity attribute to control and avoid the path selection.