ccna collaboration dumps 2018

ccna collaboration dumps 2018

// This prefix cannot be used for stateless autoconfiguration when this parameter is turned on after a specific prefix. Distribute-list 1 out rip The functional components of ISATAP are as follows: Prefix list is much more controllable than access list,ccna collaboration dumps 2018, supports incremental modification, and is more flexible For R2 , it is now in its own process 1 , while learning the route of this OE2 from R1 and R3 , how will it choose? Review Path Experiment 3 010x xxxx xxxx xxxx Associate the static route of the next hop None Image Image Provide a better next hop address. If it is 0.0.0.0 , it means the way to publish this route. Ipv6 rip 1 default-information only //In interface mode, only the default route is advertised, and other routing information is prohibited. R2(config-router)# distribute-list 1 out In a real network environment, we may encounter a situation where there are two or more routing protocols in a network environment, for example: Image Set ip next-hop 10.1.1.2 10.2.2.2 interface fast 1/0 Hostname: R4 Ip route 0.0.0.0 0.0.0.0 Education Network Next Hop IP 10 Image Ipv6 address 2001:5555::5/128 interface FastEthernet0/0 The command distribute-list out works only on the routes being redistributed by the Autonomous System Boundary Routers (ASBRs) into OSPF. It can be applied to external type 2 and external type 1 routes, but not to intra-area and interarea routes. Mpls ip There are some other messages, which are described below. Image Neighbor Probe IP BGP based policy accounting on input is disabled BGP based policy accounting on output is disabled Hardware idb is FastEthernet0/0 It can be seen from the CEF table that when PE1 receives the traffic from CE1 to CE2 at 2001:5555::5 , the label is compressed by two layers, and the outer layer is 301 , which is distributed by the P router, and the inner layer is 403 . PE1 is distributed. The protocol number in the IPv6 header is still 89 ; Ip route 1.1.1.0 255.255.255.0 serial 0/0 Local Binary prefix (high bits ) If the prefix does not match any entry in the prefix list, it will be rejected !! Attention tunnel mode Ipv6 address 2001::1/128 Version ! Path 10.1.12.2 Image 1 Router(config-rtr)# distribute-list prefix-list xxx {in | out} [interface] Set the outgoing interface of the data Complete the basic interface IP configuration . Add the following configuration on R2 : Address format: FF02:0:0:0:0:1:FFXX:XXXX , the specific correspondence is as follows: The configuration of CE1 is as follows: Y We found that on R1 , the route is not best , it is very simple, because NH is unreachable. The solution is simple, do next-hop-self on R2 on R3 1/256 !! define vrf Configuring Example 6 Deploying Distribution Lists When Republishing Between Protocols So in fact, it is very simple, as long as the prefix and mask part of the route, respectively, use the source and destination parts of the ACL to match. Image Interface loopback 0 RIP database Complete the basic interface IP configuration . Add the following configuration on R2 : For the next hop and route tag, see Volume I, page 189 . Address does not change) Ipv6 ospf 1 area 0 Probe Define multiple serial numbers under route-map . The serial number has a priority order when performing matching actions. Ip route 100.0.0.0 255.0.0.0 null0 Unassigned Multicast capability MAC address mapping for IPv6 multicast addresses 6PE basic experiment ! Switchport access vlan 20 interface vlan 10 The planning of the IS-IS network is as shown in the topology. Y Interface fast0/0 Ipv6 enable Image Image Redistribute connected level-1 exit-address-family Request message: You can request the entire routing table or request specific routing information. The dual-stack host uses HTTP to access the tunneling proxy through IPv4 . This dual-stack host may be an end user that fills in a web page. ...... Image Neighbor status tracking Route-target export 234:4 Tunnel mode gre ip EIGRP , BGP and other dynamic routes learned. Requested node multicast address corresponding to each unicast and anycast address used Note that if you use a virtual machine configuration, you must manually configure the linklocal address on the serial interface. Ipv6 router rip RIPprocess exit None You can: Image After completing this configuration, we can show it: X R2(config-router)# distribute-list 1 in fa0/0 Access-list 2 permit 192.168.3.0 The configuration of A and B is extremely simple, so I won’t say it here. PE1#show bgp vpnv6 unicast all labels Enhanced Interior Gateway Routing Protocol (EIGRP) Open Shortest Path First (OSPF) If the feature is not enabled on the local end, the data packet is either routed successfully or never routed out (discarded). At the same time, the tunnel proxy automatically applies the remote configuration of the configured tunnel on a dual-stack router connected to the IPv6 network. Once the configuration is applied on the dual-stack host and the dual-stack router, the tunnel is correctly established. The Permit/deny keyword has a different role in different deployment scenarios. !! Interface activates IPV6 Solution: Modify the routing protocol management distance Image Basic knowledge FIG Ibid, 4.0 after hang, C sends message poisoning message, theoretically 4.0 routing is C advertised to B , the principle of the horizontal division, B is not the C advertised 4.0 information, but with a level of toxicity reversal split broke this principle, B periodically to C sends 4.0 poison reverse messages to let C know, his neighbors knew a 4.0 hang message and waiting eagerly 4.0 resurrected place full of blood, another benefit of doing so is avoid loops, at least C is not from B to go visit 4.0 a.