ccnp tshoot final exam 2016

ccnp tshoot final exam 2016

4 C 1.1.1.0 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets Is 2 , 3 with AS the first comparison, 2 is MED small it is preferable; 2 with a further comparison, one of external routes it is preferably ( MED not compare) s> 172.16.10.0/24 RIP and IGRP the passive-interface does not send routing updates, but to accept routing updates If you configure the following, then the COST comparison will exceed the weight and become the most preferred comparison rule. ^10. The result found can be understood as a pointer to find the associated outbound interface: Policy-list concept For more detailed BGP state machine and neighbor relationship establishment process, please see the note document: " BGP State Machine and Neighbor Relationship Establishment Process" Cc00.043c.0000 (10.1.1.253) local Access-list 1 permit 1.1.1.0 Aggregate-address 192.168.0.0 255.255.0.0 attribute-map test // Associate route-map test works on aggregated routes LocPrf In fact, the establishment of a BGP neighbor relationship requires only one connection. The configuration shown in the following figure can also establish a BGP connection: Dhcp-bindings permit —Logs DHCP-binding permitted packets. RIP-2 RIPv2 uses multicast update Path Neighbor 1.1.1.1 route-map COST1 in neighbor 3.3.3.3 route-map COST2 in R2 ignores R1 update sent over,ccnp tshoot final exam 2016, because the "active examination", from R1 sent from the RIP updates and R2 of S0 / 0 Kou not in the same subnet, so R2 ignored R1 incoming routing updates. At this time, just validate-update-source under the RIP process of R2 . Access-list 2 permit 10.1.2.0 route-map cisco permit 10 Discard (that is , the combination of disabling, blocking, and listening in 802.1D ) Private-vlan community Vlan 102 Bgp-policy accounting input s suppressed routing entries, such as doing route summarization, suppressing details Service dhcp The PC belongs to VLAN 10 and the gateway is on SW2 . The DHCP server belongs to VLAN 100 and the gateway is on SW2 . Vlans allowed on trunk Ip community-list example 1 : ipAddress ARP ACL and relative priority of DHCP snooping database entries Two-way re-release on R2 . Under normal circumstances, R1 can learn 3.3.3.0 , and R3 can learn 1.1.1.0. Set aging time Solution 1 : Manually bind IP+MAC BGP Identifer ROUTER-ID and OSPF selected routerID consistent manner The next hop of the path is unreachable. ! At this point, the direct connection is re-released on R2 , and it is found that 1.1.1.0 has not been re-released into RIP. 200 AS100 sends 10000 routes to R2 . If R2 only wants to collect 100 routes and the rest is filtered, then the general practice is to execute the in- direction filter on R2 , because AS100 is uncontrollable for AS200 . However, this method is actually a waste of link bandwidth and network resources. When the route-map is executed, the match statement contained in the policy-list called by it will be traversed and the match action will be executed . IGRP for OSI networks Metric for redistributed routes Mobile routes Community number in aa:nn format Add to the existing community Switch(config-if)# ip address 192.168.255.254 255.255.255.0 This property may not be supported, but even if it is not supported, the route containing the property should be accepted and passed EBGP load balancing is verified. Only when the routes originate from different EBGP neighbors in the same AS and meet the equivalent load balancing, you can configure the maximum-paths x to implement load balancing. For example , the configuration is based on different ASs . The command is also invalid 200 Spanning tree is used to solve this problem R2(config)#router ospf 1 Using route reflector 23 Route-map test permit 20 match ip address prefix-list 2 set metric 200 Neighbor 4.4.4.4 remote-as 345 OSPF ! Metric Bgp cluster-id 222.222.222.222 100 i 1.1.1.1 (metric 129) from 2.2.2.2 (2.2.2.2) Configuration command 57 Distribute-list 1 out rip 201 When configuring the reflector, the client- to- client reflection is enabled by default, but if the client is fully interconnected, this command adds no to turn off the reflection between the clients. Version In doing polymerization route, using as-set produced after AS-Path list {} in the AS length number only count a AS length number within the Union AS-Path list () in the AS number length Calculate basis The configuration of SW2 is as follows: CLUSTER_LIST is a string passed the route the route reflector cluster ( Cluster ) of the ID , the AS each route in the cluster has a reflection 32bit Y Match community 11 exact-match // strict match For example, in the above figure, the network has two exit lines, which are connected to ISP1 and ISP2 respectively . If you want to let the intranet student users access the ISP1 line when accessing the external network , and the ISP2 line when the teacher network segment accesses the external network , This is not possible with traditional routing because traditional IP routing does not care about the source address of the data. This must be done with PBR .