ccnp tshoot chapter 4 exam answers

ccnp tshoot chapter 4 exam answers

Experimental topology and description 1 The Fa0/0 interface is divided into two sub-interfaces, and the encapsulation protocol Dot1Q is configured . At the same time, the traffic is tagged with VLANs , so that a trunk is started between the switch and the router . The two sub-router interfaces are arranged two VLAN gateways in the IP , as VLAN user gateway. ( Optional non-transitive ) Ip route 172.16.3.0 255.255.255.0 172.16.12.3 *>i100.0.2.0/24 65 Interface level commands. By limiting the number of ARP packets received on an interface , you can prevent the switch that enables DAI from being attacked by the DoS . Precautions: 300, ( aggregated by 300 3.3.3.3 ) // a summary route generated from AS300 , a BGP router 3.3.3.3 produced Logical aggregation of similar links 1 Y Just match this AS_PATH of 100 Origin file flash:CCIE.txt Create route-map route-map BPDU , then he will send again. Therefore, for 802.1D , the root bridge will send BPDUs to all interfaces continuously . The non-root bridge will receive BPDUs from its own root port and send BPDUs to its designated port . Non-designated ports will not send. BPDU 's will only listen. * 192.168.101.10, from 10.10.10.10, 00:12:46 ago, via Serial0/0 Route metric is 1, traffic share count is 1 If R1 R2 is established between EBGP neighbor relationship, because EBGP establish neighbor relations will check direct route, and the default TTL = 1 , and * i100.0.1.0/24 Port-Security configuration steps Set excommunity cost pre-bestpath 1 20 , the cost value will greatly affect the routing principle, will become the first rule beyond the weight value ? To maintain a consistent BGP topology, the RR does not modify certain BGP path attributes when it reflects routes . These attributes include NH . Not the routerID of R1 , because it is not necessary at all). For the interface in the forwarding and listening state, transition to the block state (in the case of link failure) Configuring Example 6 Deploying Distribution Lists When Republishing Between Protocols If ip routing is enabled , the command is ignored (but the default route Ip route 0.0.0.0 0.0.0.0 x ) is displayed ; Tunnel Tunnel interface Aggregate-address 172.16.0.0 255.255.0.0 as-set summary-only Modify the TAG of the summary LSA of the ASBR notification The above figure only makes basic BGP configuration, releases 1.0 and 2.0 on R1 , does not summarize, and 1.0 and 2.0 BGP routes received by R4 . *Mar 4 07:02:23.473: DHCPD: inconsistent relay information. 2 Vlan 10 SW1(config-if)# ip address 10.1.1.253 255.255.255.0 Accepts Inferior BPDUs *>i When the router is adjacent to the host, they learn in some way. CISCO Note: If the DHCP relay agent is enabled but DHCP snooping is disabled, the DHCP option-82 data insertion feature is not supported. 10.1.23.2 If the routes are from EBGP neighbors,ccnp tshoot chapter 4 exam answers, it is preferred that the oldest EBGP neighbor came routing, reducing the impact of roll BGP federation Router(config-router)# distance ospf external ad1 inter-area ad2 intra-area ad3 Hostname R4 interface fa0/0 None In addition, for R4 , R5 is a normal EBGP neighbor at the moment , and it is another AS64513 , and there is no relationship with me. There is a problem with the establishment of the federation. Therefore, you need to add the bgp confederation peers 64513 command on R4 . , then R4 will AS64513 regarded as its federal the EBGP the peer , while the addition AS64513 outside the AS treated as ordinary AS .