ccnp route mpls

ccnp route mpls

Ip community-list 11 permit 100:11 For experiments on specific Layer 3 switch management VLANs , see the CCNA Lab Manual By passhot. BGP routing table entry for 1.1.1.0/24, version 2 Match ip address prefix-list 1 router bgp 1 Switchport access vlan 10 Second, rule 9 , 10 skips Match length matches according to the third layer length of the packet / / See which routes are suppressed ! Of course, R3 should also be configured similarly. R4#show ip bgp 172.16.0.0 Turn on switch interfaces Port-Security will consume resources, Port-Security detects an incoming interface to each data frame to determine whether the flow method, or if there offenses. When a security interface settings violation to shutdown when the interface is in violation Switch(config)# interface fast0/1 Switch(config-if)# switchport Switch(config-if)# switchport mode access STP operation Tunnel Tunnel interface BackboneFast 5.5.5.5 Two-point bidirectional routing re-release implementation 98 Remote-ID suboption fields VTP version running VTP Domain Name VTP Pruning Mode VTP Traps Generation 3 Summarized as follows: Then 1 , 2 are compared first, 2 is preferred (because 2 has a smaller RID ); then 2 is compared with 3 ,ccnp route mpls, 2 is external , so 2 is preferred Certification Dynamic Host Configuration Protocol CASE4 : The GW configuration is as follows: Floating static route 23 Hardware-address hardware-address type Ip community-list 11 permit 100:11 We restore the experimental environment to the basic configuration: BGP neighbor relationships are as follows SW1(config)# interface fast0/23 Configure the secure address of each interface ( Secure MAC Address ) Longest match principle 10 Heavy FAQ published The CISCO IOS version prior to 12.0(22)S and 12.2(15)T does not support this feature, and older IOS versions of the router restart exist. ? Network consolidation (same protocol or different protocols) 100 i Port role: Switchport mode private-vlan host As Primary the AS , 201 of Secondary the AS , R2 can be maintained in the original R1 of BGP case of updating the routing and connection is not affected, None The GW configuration is as follows: PVST+ There are 1.1.1.0 , 2.2.2.0 routes on R1 . DHCP //trunk package protocol is dot1q BGP routing table entry for 11.11.11.0/24, version 2 25 Tiao Origin IGP, metric 0, localpref 100, valid, internal, best Originator: 1.1.1.1, Cluster list: 2.2.2.2 200 i Ip prefix-list 30 permit 30.30.30.0/24 route-map setComm permit 10 Otherwise the flag field is obtained by some calculation (as part of the verification process) Ip address 10.1.12.2 255.255.255.0 Let's review the 13 routing rules of BGP . In this lab manual, we will verify the main entries in the routing rules and familiarize ourselves with the various properties of BGP . Origin IGP, metric 0, localpref 100, valid, internal, best Neighbor 3.3.3.3 remote-as 345 Port Mode Encapsulation Status Native vlan Fa0/20 on 802.1q trunking 1 IP routing table RFC1058 When both DSAP and SSAP take a specific value of 0xff , the 802.3 frame becomes a Netware-ETHERNET frame to carry NetWare. By default, only med of routes from the same AS are compared. If you want to compare MED for all paths , you should configure this command. Also, if this option is used, it is recommended to do this throughout the AS to avoid routing loops. BPDU sending bridge ID Experimental example: Called when republishing : ccnp R4#sh ip bgp In the above figure, two routers , R1 and R2 , exchange information with each other through RIP . However, since RIPv2 sends routing updates and related messages based on multicast, once two routers activate RIP on the interface , the PC will have to consume resources to process these multicast messages that it does not need.