ccnp route 7.0 instructor lab manual

ccnp route 7.0 instructor lab manual

[Results] There is only 1.1.1.0 route in the routing table on R2 . 300 Types of BGP of AS plan shown in FIG. Both R1 and R2 inject 100.0.1.0 and 100.0.2.0 into BGP using network . We look R5 are BGP table: 2 : Clear text verification; Neighbor 10.1.13.3 route-map test out Since the flash space is very limited, it is recommended to store the file on the TFTP server. When deploying on a TFTP server, be careful to first create an empty file to correspond to the URL in the configuration command . This file is used for dhcp snooping bingding database writes (depending on the device). Half-duplex and full-duplex are the concepts of the physical layer, and the different access modes for the duplex mode of the physical layer are the concept of the data link layer, thus forming an important feature of Ethernet: the data link layer and The physical layer is relevant. Switchport private-vlan host-association 100 102 Focus on the configuration of GW : 100 ICMP redirects are always sent 86025 The network segment of the network local direct interface enters BGP , the MED value is 0 ; the network local static route enters BGP , and the MED value is 0. The problem that the static route associated with the outgoing interface is in the network OSPF and BGP AD / / View command: Show etherchannel 1 summary In fact, the establishment of a BGP neighbor relationship requires only one connection. The configuration shown in the following figure can also establish a BGP connection: Update timer update timer Vtp pruning can only be turned on in server mode S0 DCE Router os 1 Vlans allowed on trunk The DA 40bit multicast address is used to indicate that this FRAME is an ISL . Report routing information. 1.1.1.1 (metric 129) from 4.4.4.4 (4.4.4.4) IP layer connectivity. Port The TCP connection was not successfully established and the TCP connection was tried repeatedly . When a BGP router sends a route update to its EBGP neighbor, it cannot carry the LP attribute. The LP value of the EBGP route received by the peer is empty. Router bgp 345 In the port field of the circuit-ID suboption, the port numbers start at 3. That is to say, in this field,ccnp route 7.0 instructor lab manual, the port number is from 3 , the first port number is 3 , and so on. For example, a 24- port switch with an SFP slot , port3 is fast x/0/1 , port4 is fast x/0/2 , and so on, port 27 is the x/0/1 port of the sfq module . Where x is the stack member number. BGP table on R7 : Both R1 and R2 inject 100.0.1.0 and 100.0.2.0 into BGP using network . If R1 turns off auto-summary and network 1.1.1.0 mask 255.255.255.0 , then R2 can learn BGP route 1.1.1.0/24 Host address. Will be reflected to other clients, non-clients and EBGP neighbors. Match ip address prefix-list 1 route-map RP2 permit 10 10.1.13.1 BGP routing table entry for 172.16.0.0/16, version 4 Minimum path cost to the root bridge Match ip next-hop matches the next hop address to those allowed in a particular access list Weight Neighbor 2.2.2.2 peer-group IBGP_peers Sw1(config-if-range)#no switchport // Configure the L3 interface Y In AS inside, due to the presence IBGP split horizon, making BGProuter had twenty-two established between IBGP connection, in order to get the full BGP routing updates, but this is a very low scalability approach, but also brought to the network device The two effective ways to solve the IBGP scalability problem are route reflectors and federation. Compared with the federation, the route reflector has the advantage that all routers in the federation need to support and understand the federated mechanism. The route reflector only needs the RR to understand the reflector mechanism. In addition, the implementation mechanism of the route reflector is relatively simple. Of course, if you want to manage large-scale AS with various EBGP mechanisms , then the federation will be a better solution.