chapter 9 exam_ ccnp-tshoot sp2016

chapter 9 exam_ ccnp-tshoot sp2016

? The lower the value is set, the higher the protection level for the CPU . This value takes effect before and after the penalty action occurs. Of course,chapter 9 exam_ ccnp-tshoot sp2016, this value cannot be set too low. At least the legal traffic must be processed. Generally less than 1000 is almost the same. RFC1058 The above command only re-advertises OSPF NSSA routes into BGP. Route Tag Network If you want to modify the weight , let R4 go to 100.0.1.0 and go to R3 to go to 100.0.2.0 and go to R5 ? Then the configuration is modified as follows: ? 2.2.2.0 Routing Although the next hop is directed to R1 , it does not use the outbound interface to create routing entries. From the experimental phenomenon, it is not matched by the match . Needless to say, 3.3.3.0 , the associated interface is s0/1 . DHCP configuration manual binding to read bindings from the network Established The above command, the switch will accept the carry option82 information while giaddr is 0 the dhcp message, and then do the relay. In this way, the address can be successfully obtained. The implementation of diversified strategies at the level has been able to achieve very good path control effects, and it is a very scientific and highly recommended method to control the flow of data by controlling routing. In addition to this, there are many, such as: This experiment mainly verifies that automatic summarization does not occur at the boundary of the main class network: The configuration of R3 is similar. In the full-duplex mode, the transceiver can be directly sent and received without pre-determining the busy state of the link. Second column > Optimal path selected by BGP algorithm STP topology change BGP introducing and transmission routes LACP mode: It can only be mapped to the ethernet of vlan Remarks Route-map test permit 10 set community ? Clear ip bgp * Site-level site identification: Identify the various sites on the network at the data link layer. Neighbor maximum-prefix 300 90% warning-only The summary of the route is actually done by the operation of the subnet mask. For the following example: RIP redistribute directly connected If you do not set Metric , the default 1 -hop neighbor passed (the neighbors directly using this 1 jump as Metric ); redistributed static route default Metric = 1 , use the default-metric can modify this default value, this command No effect on the metric that re-releases the direct connector . Router(config-router)#redistribute ? Type echo protocol ipIcmpEcho 10.2.2.2 source-ipaddr 10.2.2.1 frequency 10 3.3.3.3 RIP Version 2 Carrying Additional Information Network R4#show ip bgp 172.16.0.0 Neighbor 10.1.23.3 dmzlink-bw The optional parameter length is used to indicate the length of the optional parameter field Layer 2 interface (switchport) : access mode, trunk mode Match ip address prefix-list 2 router bgp 100 External route tag Figure 2 R1 and R3 are the same AS , and the route of the 13 network segment is updated to R2 at the same time . The experimental effect is also in accordance with the rule description. If it is in the IBGP environment, that is, R1 , R2 , and R3 are all in one AS , then the rule Rules do not apply Origin IGP, metric 0, localpref 100, valid, external, multipath , best Route-map test deny 10 The configuration of R1 is as follows: Switch(config-if)# ip address 192.168.10.254 255.255.255.0 Switch(config-if)# no shutdown Route tag Tag 73 Set ip next-hop 10.1.1.2 10.2.2.2 interface fast 1/0 Route-map WT1 permit 20 match ip address prefix-list 2 set weight 100 0 ? Y 3.3.3.3 Switch(config-if)# switchport port-security RIP version number: Port By modifying the weight to influence the routing decision AS_PATH type 2 : AS_SEQENCE detailed 1,10,20,30 If the routes are from EBGP neighbors, it is preferred that the oldest EBGP neighbor came routing, reduce the impact of the roll (this provision mainly EBGP *>i100.0.1.0/24 O IA C In the ETHERNET_II frame, the upper layer protocol is distinguished by the Type field. At this time, it is not necessary to implement the LLC sublayer, and only one MAC sublayer is included . And IEEE802.3 frames in the LLC sublayer of the link layer in addition to the traditional definition of services, but also adds a number of other useful features. These features are provided by the DSAP , SSAP, and Control fields.