ccnp 300-101 exam vouchers

ccnp 300-101 exam vouchers

200 AS_PATH several commands 30 13 For example, the following three types of point-to-point transmission services: Route-map test permit 10 Can be detected when a violation time occurs, and can be punished Gateway of last resort is not set 9.0.0.0/24 is subnetted, 2 subnets R2(config)# access-list 1 deny 192.168.3.0 R2(config)# access-list 1 permit any R2(config)# router ospf 1 Spanning tree is used to solve this problem Public Le keyword is not written, then the default is greater than 24 less than 32 BGP , but the BGP routes ( BGP packets) between the BEs can be forwarded through the CD . For the CD , these BGP messages are regarded as normal IP packets and are directly forwarded and not viewed. The configuration of R3 is similar. Routing entry for 192.168.1.0/24 Also, when R2 hangs, the entry of 172.16.2.0/24 is invalid, and the data destined for the 2.0 subnet is matching 172.16.0.0/16. The adjacency list in the CEF component is used for MAC or Layer 2 rewrite information. Based on CEF Option 82 can contain multiple suboptions , and rfc3046 defines the following two: R2#show adjacency detail Related commands : Neighbor 10.1.12.2 route-map test out 6 switchport trunk encapsulation dot1q switchport mode trunk Internet (well-known community) A sends a data frame to B requesting to establish a reliable connection-oriented connection. Bgp deterministic-med The BGP update is carried by the TCP protocol. The port number used is 179. Because BGP requires TCP , there must be a BGP peer . Border Gateway Protocol (BGP) Connected (Note that this feature is not supported in truncated switching mode on 6509 switches ) You can also use the show ip dhcp bingding to capture the client-identifier of the client on the server. 1 : RIP-1 ; Network 192.168.254.0 0.0.0.255 area 1 Match ip address 1 router bgp 100 Last update from 10.1.12.1 00:07:30 ago Routing Descriptor Blocks: 200 i Community-List. 11 the permit IP no-export (or no-export into NO-ADV ) Access port processing frame process When 10.4.0.0 is hanged , C will immediately send a route poisoning message ( 10.4.0.0 16 hops) and then advertise it; Message age ARP ACLs take precedence over DHCP snooping database entries. After you specified the global command ip arp inspection filter Federal configuration and implementation 8 !! Two ACLs are created above to match the routes that need to be treated differently. Switchport access vlan 10 interface fast0/24 BGP routing rules 1 VLAN field, 15 bits are currently used 10 th, then the support up to 2 of the 10 power = 1024 th VLAN Part of static configuration, part of dynamic learning Conduct a three-layer forwarding decision. The CEF table maintains core information extracted from the routing table, which is used to perform forwarding decisions on received messages, including IP prefixes,ccnp 300-101 exam vouchers, recursive next hop addresses, and outbound interfaces. An important feature of the CEF table is its ability to make immediate decisions about recursive prefixes. In the above figure, the configuration revision number of server and client is the same, but the vlan information is different. At this time, an error will be reported, prompting md5 digest checksum mismatch Ip community-list 11 permit 100:11 no-advertise Next Hop Router bgp 1234 5 Weight Debug ip dhcp server {events | packets | linkage} Enables debugging on the DHCP server Make a summary on R3 , use aggregate-address summary-only as-set , note that the as-set keyword is added. Metric Origin IGP, metric 0, localpref 100, valid, external, multipath , best Interface vlan 10 Matching 100 , 101 , 102 , 103 , 104 , 109 which AS_PATH Now, we have to go through the calculations to get a summary of the segments that are just "inclusive". The next hop (the Next Hop) - if present , it identifies a better than advertised router address of the next hop address. In other words , the next hop address it noted , that in the same measure than - advertised subnet router closer to the destination. If this field is set to all 0s (0.0.0.0), the address of the advertising router is the optimal next hop address. If the BGP route is locally originated (network or the redistribute) in , carries the MED to a value EBGP Peer Local Establish BGP neighbor relations The link has failed. Can also be understood as the maximum life of this BPDU , the default 20S Ip route 2.2.2.0 255.255.255.0 192.168.13.1 The cost of the route. Enables debugging on the DHCP client Of course, on R3 , the same effect can be achieved with the distribution list in the in direction. byte At this time , OSPF routes are re-advertised to BGP on R11 , so that R12 can learn. After R12 learns the route, it finds that BGP attributes (including AS_PATH ) are lost. Because OSPF redistributed into BGP , the default does not automatically tag values are copied into the AS_PATH , the need to R11 on 5.5.5.5 ( metric 2 ) from 5.5.5.5 (5.5.5.5) Match tag 10 Turn on switch interfaces Port-Security will consume resources, Port-Security detects an incoming interface to each data frame to determine whether the flow method, or if there offenses. When a security interface settings violation to shutdown when the interface is in violation By default, as long as DAI drops the message, it will be logged Multi-hop EBGP 100 i RIP Version 2 Carrying Additional Information 10.1.13.1 Other solutions, we will continue to introduce in the following experiments Forwarder 1 State is Active Then look at the R4 's BGP table: Mismatch. This method requires that the community contains 100:11 and no-advertise to match. Configure additional verification actions The Protected port feature cannot be configured across switches: Fa0/22 1,10,20,30 Metric 100 ? The redistribute local route learned from the IGP routing protocol enters BGP , and the MED value inherits the metric in the IGP protocol. Experiment 1 PS : When the same router has two static routes to the same destination, the outbound interface and the next hop are used respectively. The two routes are load balanced (because the AD value and the metric value are equal). The static route configured by the outbound interface is imported into the routing table as a directly connected network. For details, see the static routing part of this document.