ccnp 300-101 testking

ccnp 300-101 testking

Hardware address R3 and R4 , R4 and R5 establish an IBGP neighbor relationship, and R3R4R5 uses LOOPBACK as the update source and refers to the neighbor . R3 and R4 update the routes in AS1 and AS2 to R5 and R6 at the same time . If R5 is required to go to AS1 , take route R3 and go to AS2 . So if we use a solution that re-releases static summary routes: When OSPF to IBGP when routes are heavy, because the OSPF of AD than IBGP of AD should be small, so there is no problem of sub-optimal routing path or loop: The second command is to adjust the AD value for external routes, inter-area or intra-area routes . In direction Simplify the synchronization of VLAN information bases in large campus networks (same VTP management domain) Second column > Optimal path selected by BGP algorithm R2(config-router)# distribute-list 1 in fa0/0 DAI is an ingress security feature that does not perform egress security checks. Reviewer As a result of the experiment, the PC could not get the address. The decision process of BGP is to use the local routing policy for the routes in ajd-RIBs-IN , and put the selected or modified routes into Loc-RIB and 2 Network 10.10.10.0 mask 255.255.255.0 The configuration of R1 is as follows: Command summary 81 Continue to look R4 result of the capture ( R3 distributed to R4 of BGP update package): The next hop of the A segment becomes R4 , which results in a suboptimal path. Also, on R3 , the re-release of process 1 to process 2 fails. Load balancing can be modified on AVG , but it is recommended to configure on all routers. ? MAC sublayer Route-map PBR permit 10 match ip address 1 Mapping is only valid locally R1 releases 10.0 , R2 releases 20.0 , and R3 issues 30.0 routes. Next, look at the different commands (keywords) configured on R2 . These BGP routes are learned by the specific router after the AS_PATH changes: If the local BGP advertiser becomes the next hop address, the next hop field in the local BGP RIB is 0.0.0.0. 10 Define the network segment associated with the address pool This fulfills the demand. Default route Topology change mechanism (delivery) SW2 receives the BPDU from SW3 and calculates its own Fa0/2 as the root port. Routing entry for 8.8.8.0/24 None FIG above, R1 to R2 update 1.1.1.0 , . 1 hop, when R1 DOWN off, and R3 to R2 update 1.1.1.0 is . 5 hopping, R2 up to R1 route will vary with invalid timer expires becomes pdown State, then enter the timer of the holddown timer Configuration and implementation Multicast capability 100 1 network entries using 117 bytes of memory 1 path entries using 52 bytes of memory ---------- When a data frame is sent from a trunk port, the frame is sent directly. Metric Ip route 172.16.1.0 255.255.255.0 192.168.12.1 Sw(config-if)#switchport mode private-vlan promiscuous sw(config-if)#switchport private-vlan mapping 100 201,202 sw(config)#interface range fa 0/1-2 The origin of the distance vector name is because the route is advertised in the form of a vector (distance, direction), where the distance is defined according to the metric, and the direction is defined according to the next hop router. Display all BGP routes advertised to a specific neighbor Match ip address 1 set metric 20 9.9.12.0 is directly connected, FastEthernet0/0 Tftp: Database agent URL 4. Proposal/Agreement Sequence As mentioned above, the secure address entry formed by the dynamically learned MAC address of the interface will lose the secure address entries formed by the dynamically learned MAC after the interface is up/down , but all interfaces are used. The switchport port-security mac-address is manually configured and the workload is too large. Therefore,ccnp 300-101 testking, this sticky mac address allows us to turn these dynamically learned MACs into a "sticky state " . It can be simply understood that I will learn dynamically, and after I learn, I will glue you up to form a "static". "(Effectively SecureSticky ) entries.