Free Cisco Written Dumps
For Top 50 Purchases 01:59:56

X

ccie lab south africa

CCIE Routing and Switching LAB Dumps

( 20 People are currently looking at this product )

Exam Code: CFG: LAB1、LAB1+、LAB2、LAB2+、LAB3
TS: TS1(5 sets)、TS2(3 sets)
DIAG:DIAG 1~DIAG 8(8 sets)

Certification Provider: Cisco

Certification Exam Name:CCIE Routing and Switching Lab

Update Date: Aug 23,2025

Free Cisco Written Dumps
For Top 50 Purchases
Latest Dumps
Numbers of Question & Answers

SECTION 1 LAYER 2 TECHNOLOGIES


Section 1.1: LAN Access

The following requirements were pre-configured

VTP is turned off in all switches

All required VLAN, including access-ports configuration in all relevant switches are provisioned.

All required SVI interface in all relevant switches (including IP address and subnets mask) are provisioned.

Configure the network in all sites as per the following requirements:

Access-port must immediately transition to the forwarding state upon link up, as long as they do not receive a BPDU. Use the minimal number of commands per switch to enable this feature.

If an access-port receive a BPDU, it must automatically shutdown. Use the minimal commands per switch to enable this feature.

 

Ports that were shutdown must attempt to automatically recover after 10 minutes.

None of the switches may generate a TC.


section 1.2: LAN distribution

configure the headquarters’ network as well as the large and medium office networks as per the following requirements:

all trunks must use dot1q encapsulation

negotiation of trunking protocol must be disabled in all switches

distribution switches (SW300, SW301, SW400, SW401, SW500, SW501) must initiate etherchannel negotiation using LACP

configure layer 2 etherechannels number as shown in the diagram 1: main topology and diagram 5: layer 2 connections’ (that is use only Po1 and/or Po2)

ensure that all ports included in etherchannels are effectively in use and bundled in the expected channel

access switches must see similar output as shown below:



section 1.3: LAN resiliency: spanning-tree

configure the headquarters‘network as per the following requirements:

SW300 must be the spanning-tree root bridge and must maintain a single spanning-tree instance for the following VLANs: 2000, 2002, 2004, 2006, 2008 (use instance number 2)

SW301 must be the spanning-tree root bridge and must maintain a single spanning-tree instance for the following VLANs: 2001, 2003, 2005, 2007, 2009 (use instance number 1)

 

all other VLANs, except 3001, must share the default spanning-tree instance

ensure that interface E0/2 of SW 300 and SW 301 is a dot1q trunk and that it switches frames for VLAN 3001 only

SW300, SW301, and SW 310 must not have any blocked ports for any access VLAN (2000-2009)

SW310 must have the least chance of being elected the root bridge for any VLAN

none of the three switches may run more than four instance of spanning-tree at any point in time

configure all access switches in both datacenter networks (SW110, SW111, SW210, SW211) as per the following requirements:

use 32-bit based values for the default port path cost

all four switches must use the default value for their interface cost




section 1.4: WAN switching technologies

configure the home router R70 as per following requirements:

the Ethernet WAN link must rely on a layer 2 protocol that supports authentication and layer 3 protocol negotiation

the service provider expects that R70 completes a three-way handshake by providing the expected response of a challenge requested

R70 must use the hostname R70and password CCIE (without quotes)

R70 must receive an IP address from R8 and must install a default route pointing to 201.99.8.8

ensure that R70 can successfully ping 8.8.8.8, which is located in the ISP#2 cloud

you are not allowed to configure any static route in R70 in order to achieve the previous requirements

use the pre-configured Dialer 1 interface as appropriate 

section 2 layer 3 technologies


section 2.1: OSPF in HQ

configure the headquarters network (BGP AS#65003) as per the following requirements:

both gateway routers of the headquarters network must always advertise a default route into the ospf domain

all four devices produce the exact same output as shown below. everything must match, except the dead time” counters and line order


section 2.2: OSPF in DC#1

in order to speed up OSPF convergence in the datacenter#1 network, limit the number of IP prefixes that are carried in OSPF LSAs that OSPF is preconfigured in all required devices in datacenter#1

configure the datacenter#1 network as per the following requirements:

all OSPF devices must exclude the IP prefixes of connected networks when advertising their type 1 router LSA, except for prefixes associated with loopbacks or passive interfaces

host loopbacks are the only OSPF intra-area prefixes that may appear in any DC devices ‘routing table

your solution must still apply if any new interface was added to the OSPF domain

don not use any prefix-list or another explicit filter anywhere

do not configure any interface as unnumbered

do not remove any pre-configuration


section 2.3: B2B connection with partner#1

R100 is located in the partner#1 network and is connected to R42. it supports OSPF only. configure the large office network as per the following requirements:

 

R42 must run a separate OSPF process with R100

as mentioned in item 2.6, the site gateways R40 and R41 area not allowed to redistribute OSPF into BGP and vice versa

R42 is allowed to redistribute OSPF into BGP and vice versa

At the end of the exam:

The server 2 (that is located in the Datacenter#2) must be able to ping the IP address 100.100.100.100/24 (that is located in the partner#1 network)

  R100, the partner router, must receive the external prefixes as shown below and no other prefixes:

Section 3 VPN Technology


Section 3.1: MPLS VPN

Section 3.2: DMVPN

Section 3.3: Internet Access

Section 3.4 LAN to LAN IPsec

Section 4 Infrastructure Security


Section 4.1: Device Security

Section 4.2: Network Security

Section 5 Infrastructure Security


Section 5.1: System Management

Section 5.2: Quality of Service

Section 5.3: Network Services

Section 5.4: Network Services

ccie lab south africa


Here is the most accurate CISCO CCIE WRITTEN exam questions and answers. All study materials need to be carefully selected by professional certification experts to ensure that you spend the least amount of money, time, and pass the high quality exam. There is also a professional service team that can customize your study plan for you to answer all your questions, PASSHOT's CCIE Written Dumps is definitely the biggest boost for you to test CCIE that helping you pass any Cisco exam at one time.

    ccie lab south africa

  • 5293 Reviews
  • NS: Source IP 2001::1 Destination IP FF02::1:FF00:0002 encountered practical problems, they couldn’t help themselves. The there was a bible. thing. My 2.IPV6 basic agreement sub-psychological gap has come out. I dare not face such a situation. I ability is forced out, depending on whether you have such 10.3.3.1   students put their jobs into the post after they finished the exam. At    =========================================================== ===================   10.3.3.1   (1) Route#copy tftp flash (upgrade IOS) Copy flash: tftp:   =========================================================== ===================   (5) People are divided into groups complicated situation in my work. At that time, the superstition of mcse Redundant topology , causing " broadcast storm ", " multiple frame reception ", "MAC address table instability ".   =========================================================== ===============   PS: Like most Internet companies, the cost-first concept coincides. Perhaps my career choice is also an option for the Internet. Configuring and Verifying Cut-Through Proxy Authentication 1Gbps   I chose to sleep during the day, listen to the teacher's explanations Typical application environment PCA - R (dual stack router) - PCB Enable secret   PAT configuration   Enable "diagnostic mode"? y/n [n]: n (select no) Frame-relay intf-type dce   ICMP (Internet Control Message protocol)   Rommon9>set(View) Neighbor requests multicast address: => Network map   Enter privileged mode     The freshmen who have just finished CCIE, the technical principles/commands are very familiar, but the treatment is still far away. Maybe I knocked too fast. When I knocked on 2.4 EBGP, MPLS, ***V4, VRF, and RT were all done (version Q, Main office). I admire myself and dare to do this. I suggest that you don't like me. In the end, I will slash all the way and stabilize! ! ! Because it is in this process, I was taught by the teacher TR, and I will talk about it in detail later! :: 128 0 is similar to 0.0.0.0 in IPV4 address. Uncertain IP, only source Remote Command Execution ccie test failed, and started the experiment on safety aspects such as =========================================================== ===============   NAT-PT Q6: R15 ipv6 inside redis ospf end 3.IPV6 routing protocol No ip add   I   TCP is a connection-oriented protocol. Connection-oriented protocols provide more sophisticated flow control and error control than connectionless protocols. TCP can ensure the quality of data transmission, which is more reliable than UDP, but it is slower than UDP because of the need for additional error detection and flow control. Immediate execution , immediate effect   Backplane bandwidth and port speed are the main performance indicators of the switch. Note 1: Before typing the reset button at this time, and then modify the setting speed in the HyperTerminal to 115200, remember, be sure to do so! Otherwise garbled! The transfer speed will increase a lot after restarting. The fourth place of the TR: R19's DM*** IPSEC strategy (I have a XXX!!), quite cute! ! !    Interface fastethernet 0/1   The metric is 32 bits long ,ccie lab south africa, the K values ​​are not equal , and the neighbor relationship cannot be created . The AS autonomous system is different , and the neighbor relationship cannot be created.   eager for. CCIE Layer 5 to Layer 7 Policy Control Overview Ipv6 router ospf 1    The FTP client first establishes a connection with the server's TCP port 21 to send commands. The client sends a PORT command on this channel when it needs to receive data. The PORT command contains what port the client uses to receive data. When transmitting data, the server sends data through the TCP port of its own connection to the designated port of the client. The FTP server must establish a new connection with the client to transfer data.

Have any question for us?

Cisco Dumps Popular Search:

cisco ccie r&s ine lab kit ccnp tshoot dumps free download ccnp switch quizlet ccie security version 5 lab dumps sybex ccna ccie lab exam cost ccnp route practice labs pdf cert collections ccna cost cisco ccna sample exam

Copyright © 2025 PASSHOT All rights reserved.